PIONEER CDJ-1000/TLBXJ
Manual de Usuario

OTHERS

TROUBLESHOOTING
Incorrect operations can be mistaken as malfunctions. If you believe the unit is not operating correctly, consult the chart below. Sometimes incorrect operation may be due to a malfunction in another component. If the problem is not fixed, check the other components used with the player. If the problem still persists, contact your nearest Pioneer authorized service center or dealer for service. Symptom
Disc doesn�t eject even when EJECT button (0) is pressed.

Cause
÷ Power plug is disconnected from outlet. ÷ The EJECT UNLOCK/LOCK button is set to the [LOCK] position.

Remedy
÷ Connect plug to wall outlet. ÷ Go to pause mode or cue standby mode before pressing the EJECT button (0). ÷ Set the EJECT UNLOCK/LOCK button to the [UNLOCK] position before pressing the EJECT button (0). ÷ Hold down the TIME MODE/AUTO CUE button for 1 second or longer to turn off the A. CUE function. ÷ Load the disc correctly with the label side UP. ÷ Clean the smudges from the disc and then play it again. ÷ Recheck connections. Refer to installation instructions. ÷ Check the settings of the audio mixer switches and sound volume controls. ÷ Clean away dirt. ÷ Press the PLAY/PAUSE button (6). ÷ Connect to audio mixer's LINE INPUT terminals. (Do not connect to MIC terminals.) ÷ Clean away dirt. ÷ Switch OFF TV set, move player away from TV set or plug the player into a separate outlet. ÷ Replace disc. ÷ Clean disc. ÷ Press TIME MODE/AUTO CUE button for more than 1 second to set the auto cue function OFF.

Play doesn�t commence even when the disc is inserted. Playback immediately stops when started. During playback, the player pauses or stops. No sound is audible.

÷ The auto cue function is set to on. ÷ Disc is loaded upside down. ÷ Smudges on the disc, etc. ÷ Output cables are connected incorrectly or are loose. ÷ Incorrect operation of audio mixer. ÷ Pin plugs and/or amplifier terminals are dirty. ÷ Player is in pause mode.

Sound is distorted, noise is output.

÷ Incorrect connections. ÷ Pin plugs and/or amplifier terminals are dirty. ÷ Interference is being picked up from a TV set.

With certain discs, loud noise is produced or play stops. When the auto cue function is set ON, track search is not finished.

÷ Disc has a bad scratch or warp. ÷ Disc is extremely dirty. ÷ If the sound muted portion between selections is long, searching time will be long. ÷ If the sound muted portion is recorded for about 10 seconds or more, playback will start without the auto cue function. ÷ The Cue point is not set yet. ÷ The Digital Mode switch is set to the [ON] position. ÷ No Cue points (start points) have been set. ÷ The Digital Mode switch is set to the [ON] position. ÷ The Digital Mode switch is set to the [ON] position. ÷ Incorrect JOG MODE [VINYL/CDJ] is set. ÷ The Digital Mode switch is set to the [ON] position. ÷ Interference is being picked up from the CD player. ÷ The disc rotation stops automatically if no operation has been performed for 80 minutes or more in pause mode ÷ When the last track on the disc is over the disc stops rotating.

Back cue function cannot be carried out even though the CUE button is pressed in playback mode. Pressing the LOOP OUT button does not start loop play. The Jog dial does not operate. The Jog dial does not operate as desired. DJ functions do not work. The picture of the TV screen is fluctuated or FM broadcast is interfered with noise. The disc is not rotating when power is ON.

÷ Set the Cue point. (See page 18.) ÷ The Digital Mode switch is set to the [OFF] position. ÷ Set a Cue point. ÷ The Digital Mode switch is set to the [OFF] position. ÷ The Digital Mode switch is set to the [OFF] position. ÷ Press the JOG MODE SELECT button to set the desired JOG MODE [VINYL or CDJ]. ÷ The Digital Mode switch is set to the [OFF] position. ÷ Turn off POWER switch of the player, or move the player away from the TV or tuner. ÷ Playback can be started by pressing the PLAY/PAUSE button (6). Press the EJECT button (0) to eject the disc.

¶ Static electricity and other external effects may cause this unit to malfunction. In this case, set the POWER switch to OFF, then switch it on again after the disc has come to a complete stop. ¶ This unit cannot playback unfinalized (partial discs) CD-R or CD-RW discs. ¶ This component is designed to play both 12 cm discs and 8 cm discs with a commercially available adapter, eccentrically shaped discs cannot be played since damage or malfunction may result. ¶ When using an 8cm disc with an adaptor, compared to a 12cm disc, the speed may be slower in the scratch and reverse modes etc. This component rotates at a very high speed to generate high performance, however, in the interest of safety, the speed is lowered when an 8cm disc and adaptor are used. This is NOT a malfunction. ¶ The BPM value measured by the CDJ-1000 may differ from the BPM value recorded on a CD or from our DJ mixer, but this difference is a result of differences in the BPM value measurement method; not a result of a fault with the player.

Malfunction of the MMC is NOT covered by warranty
The Multimedia Card (MMC) is not covered by warranty so we recommend you obey the instructions for use and periodically make back up copies. It is not the responsibility of PIONEER if the component or MMC malfunctions due to outside interference of static electricity etc. and if data on the MMC is damaged or lost or incidental damage occurs no indemnification will be made.

30
<DRB1312> En En/Sp