SHARP XE-A101
Guía de consulta rápida

XE-A101 Quick Start Guide
The following describes how to get your cash register ready to operate. Follow these steps when you use the cash register for the first time.

English

1

Initializing the Cash Register

2

Installing Batteries

3

Installing a Paper Roll

4

Basic Programming

5

Now, you are ready!

To ensure the cash register operates properly, initialize it using the following procedure: 1. Set the mode switch to the REG position with the power cable unplugged.

Install batteries for back-up of sales data and programmed contents. 1. Push the printer cover forward and detach it.

1. Push the paper roll release lever and install the paper roll so that the paper unrolls from the bottom.

Set the mode switch to the Z/PGM postition.

Before Starting Entries
Set the mode switch to the REG postition.

REGOFF

VOID

X/F Z/PGM

OFF VOID X/F REG Z/PGM

Setting the Time
Enter the time in 4 digits (�hhmm� format) using the 24 hour system. Press the key once to program the next item
#/ SBTL

REGOFF

VOID

X/F Z/PGM
2. Insert the paper straight into the

Enter a clerk code (1-4) and press

CLK#

.

or twice to exit the programming mode. Example: #/
SBTL

#/ SBTL

2. Insert the plug of the power cable into the AC outlet. IMPORTANT This operation must be performed without batteries loaded.

2. Open the battery cover next to the paper roll cradle.

paper inlet, and press the f key. The inserted end comes out at the printing area.
Time(2:30 p.m.)

(Once the clerk code entered, re-entry of the clerk code is not needed until the clerk is changed.)
1
Clerk code
CLK#

Setting the Date
Enter the date in 6 digits using the month-day-year format. Press the
#/ SBTL

key once to program the next item
#/ SBTL #/ SBTL

or twice to exit the programmig mode. Example:
View from rear

Registration Example
(When the Customer Pays by Cash)
CLK#

Date(March 15, 2002)

5

3. Insert three new �AA� batteries. (Batteries are not supplied with the cash register.) The buzzer will sound three times. 3. Now the cash register has been initialized. The register display will show �0.00� with �l� .

3. (For journal printing) Insert the top end of the paper into the slit in the take-up spool shaft and wind the paper two or three turns. Then place the take-up spool on the bearing.

Setting Tax Rates (%)
Specify a tax rate (%) for calculation of tax on each taxable subtotal using the following sequence:
9

1

Clerk code

Price and dept.
3
7
#/ SBTL

�
@/TM

#/ SBTL

� Tax number (1-4)* �

@/TM

�R

Price and dept.

�

�Q�
Amount tendered

View from rear

The following are supplied with your cash register. 1 paper roll 2 drawer lock keys 1 instruction manual (English) 1 instruction manual (Spanish) 1 Quick Start Guide 1 ink roller (pre-installed) 1 take-up spool

4. When the batteries are properly installed, �l� on the display will disappear. l Close the battery cover. IMPORTANT Improper use of batteries may damage the cash register. Please take the following precautions. �Be sure that the positive (+) and negative (-) poles of each battery are oriented properly. �Never mix batteries of different types. �Never mix old batteries and new ones. Please read the instruction manual for other battery handling precautions. 4. Attach the printer cover. (For receipt printing, step 3 should be omitted.)

where R: Tax rate (0.0000% to 99.9999%)x10000 (Enter the rate in 6 digits. Leading zeros may be omitted.) Q: Minimum taxable amount (0.01 to 99.99)x100 (Smallest amount for which tax must be collected. ) *Up to 4 types of tax are programmable.

Reading and Resetting
X Reports (reading) Set the mode switch to the X/F position and press . Z Reports (reading and resetling)

Example:
#/ SBTL

@/TM

@/TM

Tax 1

Tax rate(7.0000%)

Min. taxable amount($0.11)

NOTE Your cash register is pre-programmed so that you can use it with minimum set-up. To change the settings, see the instruction manual. Initial settings Departments 1-4: Taxable 1 Departments 5-8: Non-taxable

In the Z/PGM mode, press .(In this case, grand total resetting is not performed.) Flash Reports (displayed but not printed)

In the X/F mode: Press dept. key for dept. sales reports Press Press
#/ SBTL

for sales total reports for cash-in-drawer reports O(TCADH2395BHZZ)1

CH

For further information, please read the instruction manual.

Printed in Korea/Impreso en Corea