BAUKNECHT WATS 2000
Guía de consulta rápida

CONSUMPTION DATA Temperature Selector Programme Cotton Cotton Cotton Synthetic Synthetic Delicate Wool Handwash (°C) 95 60 40 60 40 40 40 30 Load (kg) 5.0 5.0 5.0 2.0 2.0 1.5 1.0 1.0 Water (l) 66* 55 55 56 56 60 60 60 Energy (kWh) 1.80 0.95 0.60 0.80 0.40 0.55 0.50 0.30 Approx. Programme Duration (hours : minutes) 2:05 2:05 2:05 1:30 1:20 0:45 0:40 0:50

PROGRAMME START Verify that the appliance is switched on. Turn on the tap and press the �Start� button. The indicator lamp of the �Start� button stops flashing and lights up. Note: If there is a power interruption or if the appliance is disconnected during the cycle, the programme will run again from the point where it was interrupted. END OF WASH CYCLE � The �End� lamp of the programme sequence indicator lights up. 1. Press the �On/Off� button to switch off the machine. 2. Turn the tap off. 3. Wait for the lid to unlock (about 1 minute). 4. Open the lid and the drum doors and unload the machine. Leave the lid open for some time to allow the inside of the appliance to dry.

CHANGE THE PROGRAMME DURING THE WASH CYCLE 1. Switch the appliance off by pressing �On/Off�. 2. Turn the programme selector knob to the new programme. 3. Switch the appliance on again by pressing �On/Off�. The �Start� button flashes. If necessary, select additional options and different spin speed. 4. Start programme by pressing the �Start� button. PAUSE/INTERRUPT A PROGRAMME If, for any reason, you wish to interrupt the programme for a certain time and continue it later: 1. Press the �On/Off� button. 2. After the desired pause, press again on the �On/Off� button. CANCEL PROGRAMME 1. Switch off the appliance by pressing �On/Off�. 2. Turn the programme selector to �Drain�. 3. Switch the appliance on again by pressing �On/Off�. The lamp of the �Start� button flashes. 4. Press the �Start� button to start the �Drain� programme.

Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. The data on the �Energy Label� refer to the programme �Cotton 60°C�. * To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

PREPARATION OF WASH CYCLE 1. Load the machine, close the drum doors and check that they are properly locked. 2. Add detergents and additives into the dispenser to no more than the �MAX� level mark, as follows: � Programme with pre and main wash � Main wash programme without prewash � Fabric softeners and conditioners � Chlorine bleach � Stain remover agents � Anti-scale agents (if necessary) 3. Press the �On/Off� button. The lamp of the �Start� button flashes. 4. Turn the programme selector knob to the desired programme. The lamp of the programme�s standard spin speed lights up.

SELECT THE DESIRED OPTION Selecting or deselecting an option can be done at any time during the programme. The option will be applied as long as the corresponding programme phase has not been executed yet. �Eco� button � The duration of the wash is extended and the max temperature reduced to save up to 40% of energy compared to a normal wash but maintaining good washing results. �Half Load� button � Can be used for small loads and lightly soiled laundry. � Reduces the water consumption especially during the rinses. Spin speed selection button
� Every programme has an automatically preset spin speed. � Press the button to set another spin speed.

� If spin speed �0� is selected, the final spin is cancelled and the programme ends with a drain cycle.

5019 412 10050