BAUKNECHT WAT 9545 D
Guía de consulta rápida

GB
CONSUMPTION DATA Programme Cotton Cotton Synthetic Synthetic 30 min 30°C Delicate Wool Handwash Temperature Selector (°C) 95** 60 60 40 30 40 40 30 Load (kg) 5.0 5.0 2.0 2.0 3.0 1.5 1.0 1.0 Water (l) 49* 48 54 50 35 50 50 35 Energy (kWh) 1.60 0.95 0.70 0.50 0.40 0.50 0.50 0.40 Programme Duration (min) * 120 120 89 74 30 45 42 25
Note: The programme stops to �Rinse Hold� at the time the �Rinse Hold� button light flashes Terminate the �Rinse Hold� option: � Press the �Rinse Hold� button again; the programme will terminate automatically with the final spin cycle for the present wash programme. � If you do not wish to spin the clothes, turn the programme knob to the Drain programme � again. � and �Start�

Spin speed reduction button � � � Every programme has an automatic predefined maximum spin speed. � Press the button to set another spin speed. � If no lamps are on, the final spinning is canceled. Start Delay button � � The Start Delay allows to run the machine at the consumer�s convenience, for example at night when electricity is cheaper. � � � � Press the Start Delay button � � to select the delay time by 1 to 19 hours; Press the Start/Pause button � �. The Start Delay � � light flashes until the programme starts. The time delay indication � � disappears when the programme starts and it�s replaced by the remaining time. The number of hours preselected can later be reduced pressing again the Start Delay button � �.

Prewash cycle increases programme duration by 5 to 20 min. Consumption values were measured in normalized conditions in compliance with Standard IEC 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. *The remaining time indicator can similarly deviate from the values in the table, because it takes into account the household **To conditions applicable at that time. reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

ADDING DETERGENT AND ADDITIVES
Add the detergent and the additives into the dispenser as follows: � Programme with pre and main wash � � � Main wash programme without prewash Fabric softeners and conditioners Stain remover agents

To cancel the �Start Delay�. � Turn the programme selector to the � � position. � Reselect the desired programme and options and press the Start/Pause button �

�.

PROGRAMME START
Open the tap and press the Start/Pause button � �. The pilot lamp of the �Start/Pause� button lights up. The indicator lamps show the sequence reached in the programme. After starting the programme, the sequence indication runs from left to right through Wash � is finished the corresponding lamps goes out. �, Rinse � �, Spin � �. When the sequence of the programme

� Anti-scale agents (water hardness 4) Important: � � � Be careful not to fill more than the �MAX� level mark. For programmes without prewash from cold to 40° C it is recommended to use a liquid detergent to avoid whitish residues on the coloured laundry. With a Start delay, use a dose aid for liquid detergent, placed directly in the drum.

DOOR LOCK
During the running programme the door can be opened for adding further laundry. The door locks automatically in all rinsing and spinning cycles. If the programme is stopped or the electrical power supply is terminated, the door lock will open after approximately 1 minute.

PROGRAMME END
� 1. 2. 3. 1. 2. 3. The remaining time is on �0:00� and all the lights of the programme sequence indication are �Off�. A short audible tone sounds three times. Turn the programme selector to the position � �. Turn the water supply tap off. Open the door and the drum flaps and unload the machine. Press the Start/Pause button � � to pause the programme. The light flashes. Select the new programme (with temperature), any options and another spin speed if you want it. Press the Start/Pause button � � again. The programme continues at the same position of the programme sequence indication. Do not add detergent for this programme. Press the Start/Pause button � � to pause the programme. The lights flashes. Set the programme selector to Drain � �. The spin indications are off and the remaining time shows 2 minutes. Press the Start/Pause button � � to start the drain programme.

CLOSE THE DOOR AND SELECT THE PROGRAMME
1. 2. Turn the programme selector knob to the desired programme with its predefined temperature. The remaining time display � � shows the duration of the chosen programme (in hours and minutes) and the pilot lamp of the Start/Pause button � � is flashing. The programme sequence and the predefined spin speed indication corresponding to the selected programme lights up.

SELECTING A NEW PROGRAMME, SPIN SPEED, OPTIONS AFTER PROGRAMME START

PRESS ANY DESIRED OPTION BUTTON(S). The pilot lamp lights up.
An audible tone sounds if the combination of programme and additional options is not possible. Unsuitable combinations of options are deselected automatically Prewash button � � � Only for heavily soiled loads (for example sand, granular dirt) sensible. The cycle time increases from 5 to 20 min. Intensive Rinse button � � � The water level and the cycle time increase for improved rinsing efficiency. � This option is particularly suitable for areas with very soft water washing baby linen and helps people with allergies. Rinse Hold button � � � The laundry remains in the last rinse water without progressing to the final spin cycle to avoid creasing and prevent colours from changing. � � This option is particularly recommended for the programme Synthetic � � or Delicate � This function is particularly useful if you want to postpone spinning to a later time. �.

TO STOP, RESET A PROGRAMME BEFORE THE END
1. 2. 3.

AUTOMATIC SAFETY FUNCTIONS / FAULTS
This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately. Often, however, the faults detected are small enough to be solved in a matter of minutes. Informations can be found in the �Troubleshooting Guide�.

5019 100 12665