HARTKE VX410
Manual de Usuario

Connecting the VX410 and VX410a
About Impedance Before you hook up your speaker cabinet be sure that you understand a little about impedance. Impedance is the electronic load that the speaker puts on the power amplifier and is measured in Ohms. Here is the tricky, yet simple rule of impedance; When two speakers are wired in "Parallel" the total impedance is cut in half and when two speakers are wire is �Series� the total impedance is the sum of the
EFFECT

Hartke Systems
Distributed Exclusively by Samson Technologies Corp. Hicksville, New York 11802

MODEL 2000 200 WATTS 8 = 120 WATTS 4 = 200 WATTS

115

~ AC INPUT 115V/230V 50/60Hz FUSE 5A/250V, 180W (115V) 2.5A/250V, 450W (230V)

RETUIRN

SPEAKER OUTPUTS

SEND

CAUTION TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE TO RAIN OR MOISTURE. SERIAL NUMBER

HPF

OFF

ON

8

8

ASSEMBLED IN R.O.K.

speakers individual impedance. The VX410 and VX410a�s impedance (many audio guys used the made up word �ohmage�, however the correct term is impedance) is 8 Ohms. So, when two VX410�sor VX410a�s are connected together in parallel the total impedance is 4 Ohms. The impedance of your speaker also has an effect on you amplifier. In general, the lower the impedance the more power your amplifier will put out. IMPORTANT: There is an minimum safe impedance so be sure to check the manufacturer�s recommended impedance for your amplifier to avoid any damage to your amplifier or voiding your warranty. Connecting the VX410 to Your Amplifier The VX410 and VX410a connections are made via 1/4� phone jacks located on the rear panel jack-plate. Be sure to make your connection with un-shielded speaker cable. Connect the Amplifier Output to the speaker Input on the VX410�s rear jackplate. Using the EXTENSION Output The VX410and VX410a provides a convenient Extension Output for connecting additional speaker cabinets in parallel. Be sure to read the section above on impedance to insure a proper hook up with your amplifier. Follow the steps below to connect two VX410�s using the Extension Output. Connect the Amplifier Output to the Input of the first VX410. Now, connect the Extension Output to the Input of the second VX410 or VX410a.
Hartke
-series
Hartke Systems Distributed worldwide by Samson Technologies

VX410 BASS CABINET 400 WATTS

INPUTS

8

EXTENSION

SERIAL NUMBER

MADE IN CHINA

www.hartke.com

CAUTION TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE TO RAIN OR MOISTURE. SERIAL NUMBER ASSEMBLED IN R.O.K.

MODEL 2000 200 WATTS 8 = 120 WATTS 4 = 200 WATTS

115

Hartke Systems
Distributed Exclusively by Samson Technologies Corp. Hicksville, New York 11802

EFFECT

~ AC INPUT 115V/230V 50/60Hz FUSE 5A/250V, 180W (115V) 2.5A/250V, 450W (230V)

RETUIRN

SEND

SPEAKER OUTPUTS

HPF OFF ON
8 8

Hartke
-series
VX410 BASS CABINET 400 WATTS
Hartke Systems Distributed worldwide by Samson Technologies

INPUTS

8

EXTENSION

SERIAL NUMBER

MADE IN CHINA

www.hartke.com

Hartke
-series
Hartke Systems Distributed worldwide by Samson Technologies

VX410 BASS CABINET 400 WATTS

INPUTS

8

EXTENSION

SERIAL NUMBER

MADE IN CHINA

www.hartke.com