KENWOOD TK780H
Manual de Servicio

TK-780/H
REALIGNMENT
Notes :
� To start the Firmware Programmer from KPG-49D, the FPRO path must be set up by KPG-49D setup. � This mode cannot be entered if the Firmware programming mode is set to Disable in the Programming software (KPG-49D). � When programming the firmware, it is recommend to copy the data from the floppy disk to your hard disk before update the radio firmware. Directly copying from the floppy disk to the radio may not work because the access speed is too slow. How to enter the password with the [System up/down] key (Trunking format), the [Group up/down] key (Conventional format); If the [System up/down] key (Trunking format), the [Group up/down] key (Conventional format) is pressed while �CLONE LOCK� is displayed, numbers (0 to 9) are displayed flashing. When you press the [SCN] key, the currently selected number is determined, and the display shifts to the left. If you press the [SCN] key after entering the password in this procedure, �CLONE MODE� is displayed if the entered password is correct. If the password is incorrect, �CLONE LOCK� is redisplayed. Power on the slave TK-780/780H. Connect the cloning cable (No. E30-3382-05) to the modular microphone jacks on the master and slave. Press the [S] key on the master while the master displays �CLONE MODE�. The data of the master is sent to the slave. While the slave is receiving the data, �PROGRAM� is displayed. When cloning of data is completed, the mater displays �END�, and the slave automatically operates in the User mode. The slave can then be operated by the same program as the master. The other slave can be continuously cloned. When the [S] key on the master is pressed while the master displays �END�, the master displays �CLONE MODE�. Carry out the operation in step 4 to 6.

6-4. Function
1. If you press the [MON] switch while �PROG 57600� is displayed, the checksum is displayed. If you press the [MON] switch again while the checksum is displayed, �PROG 57600� is redisplayed. 2. If you press the [D] switch while �PROG 57600� is displayed, the display changes to �PROG 19200� to indicate that the write speed is low speed (19200 bps). If you press the [D] switch again while �PROG 19200� is displayed, the display changes to �PROG 38400�, and the write speed becomes the middle speed (38400 bps). If you press the [D] switch again while �PROG 38400� is displayed, the display returns to �PROG 57600�.

4. 5. 6.

7.

Note :

Normally, write in the high-speed mode.

Note :
Only the same models can be cloned together.

7. Clone Mode
Programming data can be transferred from one radio to another by connecting them via their modular microphone jacks. The operation is as follows (the transmit radio is the master and the receive radio is a slave). 1. Turn the master TK-780/780H power ON with the [C] key held down. If the password is set to the TK-780/780H, the TK-780/780H displays �CLONE LOCK�. If the password is not set, the TK-780/780H displays �CLONE MODE�. 2. When �CLONE LOCK� is displayed, only the [System up/ down] key (Trunking format), the [Group up/down] key (Conventional format) and [SCN], and [0] to [9] keys can be accepted. When you enter the correct password, and �CLONE MODE� is displayed, the TK-780/780H can be used as the cloning master. The following describes how to enter the password. 3. How to enter the password with the microphone keypad. If you press a key while �CLONE LOCK� is displayed, the number that was pressed is displayed on the TK-780/ 780H. Each press of the key shifts the display in order to the left. When you enter the password and press the [SCN] key, �CLONE MODE� is displayed if the entered password is correct. If the password is incorrect, �CLONE LOCK� is redisplayed.

Cloning cable (E30-3382-05)

Fig. 2

17