TOSHIBA TDP-S20
Manual de Usuario

Basic operations
1 Turn on the power.
Turn on the power by following the instructions in �Turning on the power� p.22 .

5 Projector placement angle adjustments
The placement angle and the height of the projected image can be adjusted by the foot adjuster.

2 Select the language and the lamp power (When using the
first time).
When the projector is used for the first time after purchase, menu for language and lamp power selection and configuration is displayed in English. (If the screen is out of focus, adjust it according to the step 6 .) ................
English Français .............. Deutsch .............. Italiano ................ Español ............... Português .......... Russian ............... Swedish .............. Türkçe ................ ................. ....... ....... ................... English French German Italian Spanish Portuguese Russian Swedish Turkish Japanese Chinese (simplified) Chinese (traditional) Korean

q Lift up the front of the projector to the desired angle, then press the foot adjuster release button.
The foot adjuster extends. Release the button to lock the position.

1

q Use the or button to select the desired language and press the button.
Message for setup confirmation is displayed in a selected language. Then, the menu for lamp power selection and configuration is displayed. It is automatically set as Standard. To change the setting, follow the step w.

w Turn the foot adjuster to fine-tune the angle. e To adjust the horizontal angle, use the tilt adjuster.

3

2

To stow the foot adjuster, hold up the projector while pressing the foot adjuster release button, then slowly lower the projector.

w Using the

or

button, select Standard

6 Adjusting the screen size and focus
q Use the zooming lever to adjust the screen size. w Use the focusing lever to adjust the focus.
1

or Low for the lamp power (menu item) and press the button.
The lamp power, if selected, will be toggled without pressing the button. The display automatically disappears in a few seconds.

2

Notes
� When the projector is turned on the next time, the Language and Lamp power menus do not appear upon startup. However, if �Reset all� is executed from the Default setting menu p.32 , the Language and Lamp power menus will be displayed the next time when the power is turned on. � The language can also be set via the Display setting menu p.31 and Lamp power via the Default setting menu p.32 . � This owner�s manual assumes that English has been selected.

7 Adjusting the volume with the
Notes

buttons

The speaker volume can be adjusted when an audio signal is being input.

� Note that a lamp characteristics may rarely cause the brightness to fluctuate slightly. � A lamp is consumable item. If used for extended periods, images will appear dark, and the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime of the lamp depends on conditions of use.) � The DMDTM is made using extremely advanced technology, but there may be black spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please note that these are not malfunctions. Although this projector supports a wide range of RGB signals p.45 , any resolutions not supported by this projector (SVGA) will be expanded or shrunk, which will affect image quality slightly. To view high-quality images, it is recommended that the computer�s external output should be set to SVGA (800 � 600) resolution. With some models of computer having LCD displays or the like, displaying images simultaneously on the projector and the monitor�s display may prevent the images from displaying properly. If this happens, turn off the computer�s LCD display. For information on how to turn off the LCD display, see the owner�s manual of your computer. If a signal not supported by the projector is input, the �Unsupported signal� will appear. If no signal is being input from the connected device, the �No signal� will appear. If an unavailable operation button is pressed, the icon will appear.

3 Activate the connected device.
Turn on and start the connected device such as a computer. �

4 Press the INPUT button.
An image of the connected equipment is projected. Each time you press the INPUT button, it switches to the input of the connected equipment. �

Notes
� When [Auto input search] is set to [On] in the default setting menu p.32 , the image of the equipment which is connected and turned on is projected. � Moving pictures generated with the DVD software for computers may appear unnatural if it is projected with this projector, but it is not a malfunction. � � �

24

25

Operations