Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5613 visitantes y 
22 usuarios online.
Productos
Información
Destacado
Inicio >> SONY >> SPPS2730 Manual de Servicio
 
 0 artículo(s) en Su carrito 

SONY SPPS2730
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del SONY SPPS2730 Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages: English

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
SPP-S2730 SECTION 5 ELECTRICAL ADJUSTMENTS
0 dBm = 0.775 V BASE UNIT
� Make the set in the test mode. (See page 13) 1. Power Failure Test Procedure: 1. Connect between TP338 and TP306 (GND) on the BASE MAIN board by lead wire. 2. In the test mode idling status, press the [1] key to display �TEST A�. 3. Check that the [NEW CALL] LED on the base unit lights up when connect between TP203 and TP306 (GND) on the BASE MAIN board. 2. Ring Detection Test Procedure: 1. In the �TEST A� status, connect the base unit to telephone line. 2. Check that the LCD back light on the base unit lights up when call the base unit. 3. Line Closing of Parallel Connected Another Telephone Detection (On Hook) Test Procedure: 1. In the �TEST A� status, connect the base unit to telephone line. 2. Connect this set and another telephone in parallel to one telephone line. 3. Check that the [NEW CALL] LED on the base unit lights up when take up the receiver of another telephone. 4. Automatically Hold Canceling Test Procedure: 1. In the test mode idling status, press the [4] key to display �TEST D�. 2. Connect the base unit and another telephone in parallel to one telephone line. 3. Take up the local handset of base unit, and press the [HOLD] key to hold. 4. Check that the [NEW CALL] LED on the base unit lights up when take up the local handset of another telephone. 5. C-ID Input Level Measurement Setting:
feeding bridge Line Line Trunk Base unit TP101 TP102 Trunk

5.

Between Microphone and Line Signal Level Measurement Setting:
feeding bridge Line Line Base unit TP101 TP102

600 � Input Output GND audio analyzer 1.2 kHz, �27 dBm LPF: 30 kHz ON 10 µF + TP475 TP306 (GND)

Procedure: 1. Connect equipments as the figure above. 2. In the test mode idling status, press the [6] key to display �TEST F�, and press the [5] key to set the speaker path test 2 mode. 3. Set the output level of audio analyzer to �27 dBm (1.2 kHz, LPF=30 kHz ON). 4. Check that the value of audio analyzer is �2 to �8 dBm. 5. Press the [VOL --] key to return the test mode idling status. Press the [6] key to display �TEST F� again, and press the [4] key to set the speaker path test 1 mode. 6. Change the output level of audio analyzer to �36 dBm. 7. Check that the value of audio analyzer is �2 to �8 dBm. Between Line and Speaker Signal Level Measurement Setting:
feeding bridge Line Line Trunk Base unit TP101 TP102

7.

Output Input

100 µF TP476 16 �

GND audio analyzer 1.2 kHz, �27 dBm LPF: 30 kHz ON 100 µF

TP477 (SP GND)

Output Input GND audio analyzer 1.2 kHz, �17 dBm LPF: 30 kHz ON TP413 TP306 (GND)

Procedure: 1. Connect equipments as the figure above. 2. In the test mode idling status, press the [6] key to display [4] key to set the speaker path test 1 �TEST F�, and press the mode. 3. Set the output level of audio analyzer to �27 dBm (1.2 kHz, LPF=30 kHz ON). 4. Check that the value of audio analyzer is �2 to �8 dBm.

Procedure: 1. Connect equipments as the figure above. 2. In the test mode idling status, press the [6] key to display �TEST F�. 3. Set the output level of audio analyzer to �17 dBm (1.2 kHz, LPF=30 kHz ON). 4. Check that the value of audio analyzer is �15 to �21 dBm.

20

Quizás también quiera comprar

$4.99

SPPS2730 SONY
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …
>
Parse Time: 0.18 - Number of Queries: 101 - Query Time: 0.045