SONY SLV-D910B
Manual de Servicio

SLV-D910AZ/D910B/D910E/D910N/D910R/ D950B/D950E/D950GI

1. GENERAL
Getting Started

This section is extracted from SLV-D910B/D950B instruction manual. (3-084-916-E2)

Step 1 : Unpacking
Check that you have received the following items with the DVD-VCR: � Remote commander � PERITEL cable

Step 2 : Setting up the remote commander
Inserting the batteries
Insert two size AA (R6) batteries by matching the + and � on the batteries to the diagram inside the battery compartment. Insert the negative (�) end first, then push in and down until the positive (+) end clicks into position.
Getting Started Getting Started

� R6 (size AA) batteries

� Audio cord (pinplug �2 y pinplug �2)

Using the remote commander
You can use this remote commander to operate this DVDVCR and a Sony TV. Buttons on the remote commander marked with a dot (�) can be used to operate your Sony TV. If the TV does not have the symbol near the remote sensor, this remote commander will not operate the TV.

Remote sensor

� Aerial cable

� Video cord (pinplug �1 y pinplug �1)

TV / DVD·VIDEO SELECT VIDEO SELECT DVD

To operate the DVD player

Set TV / DVD·VIDEO to DVD·VIDEO, then press SELECT DVD and point at the remote sensor at the DVD-VCR DVD·VIDEO, then press SELECT VIDEO and point at the remote sensor at the DVD-VCR TV and point at the remote sensor at your TV

Check your model name
The instructions in this manual are for the 2 models: SLV-D950B and SLV-D910B. Check your model name by looking at the rear panel of your DVD-VCR. SLV-D950B is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, �SLV-D950B only�.

the VCR your TV

Notes � With normal use, the batteries should last about three to six months. � If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage. � Do not use a new battery with an old one. � Do not use different types of batteries. � Do not leave the remote commander in an extremely hot or humid place. � Do not drop any foreign object into the remote casing, particularly when replacing the batteries. � Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so may cause a malfunction. continued

8

Unpacking

Setting up the remote commander

9

Controlling other TVs with the remote commander
The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the following table, set the appropriate manufacturer�s code number.

Step 3 : Connecting the DVD-VCR
Note that �Advanced Hookups� (page 59) explains additional hookup methods that will optimize the picture and sound for a true �hometheatre� experience.

1 Set TV / DVD·VIDEO at the top of the remote commander to TV. 2 Hold down ?/1, and enter your TV�s code number using the number buttons. Then release ?/1.
Now you can use the ?/1, VOL +/�, PROG +/�, MUTING�, TV/VIDEO, 0-9 and -/--� buttons to control your TV. You can also use the buttons marked with a dot (�) to control a Sony TV. To control the DVD-VCR, reset TV / DVD·VIDEO to DVD·VIDEO.
� for Sony TV only

ANTENNE ENTREE PERITEL Aerial cable (supplied)

LINE-1 (EURO AV)

Mains lead to mains

Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the one that works with your TV. Manufacturer Sony Akai Ferguson Grundig Hitachi JVC Loewe Mivar NEC Nokia
Notes � If you enter a new code number, the code number previously entered will be erased. � If the TV uses a different remote control system from the one programmed to work with the DVD-VCR, you cannot control your TV with the remote commander. � When you replace the batteries of the remote commander, the code number may change. Set the appropriate code number every time you replace the batteries.

Code number 01, 02 68 52 10, 11 24 33 45 09, 70 66 15, 16, 69

Manufacturer Panasonic Philips Saba Samsung Sanyo Sharp Telefunken Thomson Toshiba

Code number 17, 49 06, 07, 08 12, 13 22, 23 25 29 36 43 38

: Signal flow

PERITEL cable (supplied)

1

Disconnect the aerial cable from your TV and connect it to on the rear panel of the DVD-VCR.

2 3

Connect of the DVD-VCR and the aerial input of your TV using the supplied aerial cable.

Connect LINE-1 (EURO AV) on the DVD-VCR and the PERITEL connector on the TV with the supplied PERITEL cable. This connection improves picture and sound quality. Whenever you want to watch the DVD-VCR picture, press TV/VIDEO to display the VCR indicator in the display window.

4

Connect the mains lead to the mains.

continued

10

Setting up the remote commander

Connecting the DVD-VCR

11

1-1