THOMSON ROC3205
Manual de Usuario

Checking the programming: Your product should be ready to receive remote control commands. Check to see that your remote functions correctly by performing the test described on page 3. Method B - 3-digit codes programming Before you start programming, you must find the code for the product to be controlled (television set, satellite receiver or DVD player). Refer to the list provided with these instructions, on page II of the codes. 1. Turn on the product you want to control. 2. Hold down the SETUP (11) until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). 3. Press the product key (2) that corresponds to the type of product you want to control: TV: television set, DVD: DVD player, SAT: satellite receiver. 4. While the indicator is lit, enter the 3-digit code proposed for the product to be controlled (example: 036 for THOMSON). The red indicator then goes off if the code is correct or flashes, if the code is not on the list. 5. Point the remote control towards the product and try to turn it off by pressing the POWER (12) key. 6. If the product doesn�t turn off, repeat step 2, using the next 3-digit code in the list. Try to turn off the product by pressing POWER (12) key once. Repeat this procedure until one of the 3-digit codes works. Checking the programming: Your product should be ready to receive remote control commands. Check to see that your remote functions correctly by performing the test described on page 3. Method C - Programming by means of code retrieval If none of the codes work, you may still be able to retrieve the appropriate code. 1. Turn on the product you want to control. 2. Hold down the SETUP (11) key until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). 3. Press the product key (2) that corresponds to the type of product you want to control: TV: television set, DVD: DVD player, SAT: satellite receiver. 4. Point the remote control towards the product and try to turn it off by pressing the POWER (12) key. 5. If the appliance to be controlled switches off, press the MUTE (15) key to memorise the code. 6. If the product does not turn off, press the POWER (12) key until the product switches off (up to 200 times).Wait approximately one second between key presses to give the red indicator lamp (1) enough time to go off and light up again.This will allow you to see whether the product responds or not. 7. Immediately upon turning off the product to be controlled, press the MUTE (15) key to save the code.

Note: If you want to assign another type of product than those mentioned on the remote control, begin by entering a code that corresponds to the product you want to programme (a 3-digit code that you will find in the code booklet � see method B). Example: if you want to control a satellite receiver with the DVD key, begin by entering a satellite code (any satellite, for example: 603 for a Thomson satellite receiver) then begin the procedure. Checking the programming: Your product should be ready to receive remote control commands.Check to see that your remote functions correctly by performing the test described on page 3. Method D - Automatic code search With this method, the remote scrolls through the full code list by sending an IR signal to the product to be controlled remotely. 1. Check that your product is on. If not, turn it on manually. 2. Hold down the SETUP (11) key until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). 3. Release the SETUP key. 4. Press the product key (2) corresponding to the type of product you want to control: (for example TV). 5. Press PROG+ (14). After a few seconds, the remote begins to scroll through the code list at approximately 1 code per second. Press PROG+ (14) once again to slow down the test speed (1 code every 3 seconds). As soon as the product changes channels, press the MUTE (15) key to save the code and stop the remote from scrolling through the list. If you have gone past the code, you can go back to the previous code by pressing PROG- (14) as many times as necessary (you can go forward by pressing POWER (12) or PROG+ (14). As soon as the product responds again, press the MUTE (15) key to save the code. Note: If you want to assign another type of product than those mentioned on the remote control, begin by entering a code that corresponds to the product you want to programme (a 3-digit code that you will find in the code booklet � see method B). Example: if you want to control a satellite receiver with the DVD key, begin by entering a satellite code (any satellite, for example: 603 for a Thomson satellite receiver) then begin the procedure. Method E - Programming for control of a COMBO TV/VCR,TV/DVD) Depending on the COMBO group (TV/VCR,VCR/DVD, etc.) and the make, you will be required to enter a single code for both devices in the COMBO, or to enter two codes, one code per device. Consult the separate list to discover this. Before you start programming, you must find the subcode or code of the subset to be controlled (television or video recorder). Refer to the list supplied with this user manual (see page subcodes or codes).

EN

2