JVC RM-P210U
Manual de Usuario

MENU OPERATION

GENERAL
an erroneous operation is performed.
Displayed Message Cause Check Point
HIGH

SYSTEM RESET MENU WARNING MESSAGES

This menu resets values set by user to initial values. To prevent operational errors, LCD display shows one of the following warning messages when

FULL AUTO F1 F3 MENU/SHUTTER GAIN P

SHUTTER STEP

STR 1/1000 ALC

BARS R F2 F4 MENU LOW

GAIN : LOLUX adjust the gain again. INVALID ENTRY The is ON. Press the FULL AUTO button so that FULL AUTO : ON the lamp in it turns off, then retry Control knob INVALID ENTRY is ON. Exit from the ACC+EEI mode, and then GAIN : ALC + EEI retry operation. LCD display shows menu display. Then turn the INVALID ENTRY The is set to Cancel FAW and start the white-balance control knob move the cursor ( ) to "7: SYSTEM REW.BAL : FAW mode. adjustment.

CMP +9dB LUX PUSH-ON

SHUTTER VARIABLE MID

INVALID ENTRY The gain is set to mode. Exit from the LoLux mode, and then

GAIN

M DOWN UP

LCD display MENU button

operation.

1. Press and hold the MENU button (approx. 1 second) until 6: LCD MODE 1.
7: SYSTEM RESET
INVALID ENTRY The W.BAL button is set to PRESET. Auto white balance adjustment cannot W.BAL : PRESET be started in this mode. SET".

7A: SYSTEM RESET
W.BAL : MANUAL manual mode by the AUTO/MANU button. be started in this mode. INVALID ENTRY The is pressed. Press BARS button so that the Press control knob move the cursor ( ) to "CANCEL". If do not want to reset the values you have set,

2.

CANCEL INVALID ENTRY The is set to Auto white balance adjustment cannot

3.

7A: SYSTEM RESET 2. Press the control knob to display "7A: SYSTEM RESET". BARS : ON lamp in it turns off, then retry operation.

3.

CANCEL

4.
If you want reset values, turn the control knob to ERROR MESSAGES

press the control knob now. 7A: SYSTEM RESET

4.
When LCD display shows one of the following error messages during an auto white balance adjustment AUTO SET mode, check �Cause� �Check Point� below and then retry the auto
move the cursor ( ) to "OK". white balance adjustment. (The error message is displayed for about 5 seconds.) STR OFF ALC

OK

CMP 0dB LUX 5. Press control knob reset the values you have set to
initial values and return to the normal display. AUTO WHITE A (B) The light intensity is insufficient. Increase the lighting (illumination) or

5.
Displayed Message Cause Check Point (Note that the sensitivity deteriorates

Initial values ERROR: LOW LIGHT boost gain with the GAIN button.

� The you've set in menu items will be reset the initial values shown on pages 21 to 27. when the gain is boosted.) � Other status settings are reset as shown below. AUTO WHITE A (B) The not suitable for shooting. Check if the object is white and change

Status Setting Initial Values GAIN

IRIS button AUTO STEP switch Switch position NG: OBJECT the object if required.

W.BAL switch Switch position V.GAIN LEVEL 0.1 dB

PAINT button SHUTTER OFF ERROR: OVER LIGHT sun, is shining into the camera ei-

A Central value of the control tion caused by the object.

Bch V.SCAN LEVEL Approx.1/100(U),1/120(E) ther directly or as result of a reflec-

AUTO WHITE A (B) The amount of incident is too high. � Check if a strong light source, such as SHUTTER

Rch FULL AUTO OFF B Central value of the control

WHITE PAINT

Bch OFF BARS The fil� Set the color temperature conversion

Rch F1 F4 buttons Initial value, OFF ter is not set properly. filter to the correct position.

MANUAL PAINT Central value of the control AUTO BLACK LENS NOT CLOSED? The will not close for auto black-balSet camera so that the lens can be

Bch LOLUX OFF

Rch ALC+EEI OFF ance adjustment. closed.
AUTO BLACK ERROR! Auto black adjustment is not working Check setups of the RM-210 and properly. camera again.

E-26 27U 28U E-27