Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 6043 visitantes online.
Productos
Información
Destacado
Inicio >> SHARP >> R-209(W) Manual de Servicio
 
 0 artículo(s) en Su carrito 

SHARP R-209(W)
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del SHARP R-209(W) Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages: English

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
R-209(IN) R-209(W) R-209(Y)

TURNTABLE MOTOR REMOVAL
Removal
1. Disconnect the oven from the power supply. 2. Remove the turntable and turntable support from the oven cavity. 3. Turn the oven over. 4. Remove the one (1) screw holding the turntable motor cover to the bottom plate. 5. Now, the turntable motor cover is free. 6. Disconnect the wire leads from the turntable motor. 7. Remove the single (1) screw holding the turntable motor to the oven cavity. 8. Remove the turntable motor from the oven cavity. 9. Remove the TTM packing from the turntable motor. 10.Now, the turntable motor is free.

Re-install
1. Re-install the TTM packing. 2. Re-install the turntable motor with theTTM packing with the single (1) screw. 3. Re-connect the wire leads to the turntable motor. 4. Insert the tab of the turntable motor cover into the hole of the bottom plate. 5. Re-install the turntable motor cover to the bottom plate with one (1) screw.
TTM packing

Turntable motor

Figure C-2. TTM packing Installation

COOLING FAN MOTOR REMOVAL
REMOVAL 1. CARRY OUT 3D CHECKS. 2. Remove the magnetron from the waveguide. Refer to chapter "MAGNETRON REMOVAL" 3. Disconnect the wire leads from the fan motor. 4. Disconnect the wire lead from the disconnect the fan duct. 5. Remove the three (3) screws holding the fan duct to the oven cavity. 6. Release the fan motor assembly from the oven cavity. 7. Remove the fan blade from the fan motor shaft according to the following procedure. 8. Hold the edge of the rotor of the fan motor by using a pair of groove joint pliers. CAUTION: � Make sure that any pieces do not enter the gap between the rotor and the stator of the fan motor. Because the rotor is easy to be shaven by pliers and metal pieces may be produced. � Do not touch the pliers to the coil of the fan motor because the coil may be cut or injured. � Do not disfigure the bracket by touching with the pliers. 9. Remove the fan blade assembly from the shaft of the fan motor by pulling and rotating the fan blade with your hand. 10.Now, the fan blade will be free. CAUTION: � Do not re-use the removed fan blade because the hole (for shaft) may be larger than normal.
Coil Groove joint pliers

11.Remove the two (2) screws holding the fan motor to the fan duct. 12.Now, the fan motor is free.

INSTALLATION 1. Install the fan motor to the fan duct with the two (2) screws. 2. Install the fan blade to the fan motor shaft according to the following procedure. 3. Hold the center of the bracket which supports the shaft of the fan motor on the flat table. 4. Apply the screw lock tight into the hole (for shaft) of the fan blade. 5. Install the fan blade to the shaft of fan motor by pushing the fan blade with a small, light weight, ball peen hammer or rubber mallet. CAUTION: � Do not hit the fan blade strongly when installed because the bracket may be transformed. � Make sure that the fan blade rotates smooth after installed. � Make sure that the axis of the shaft is not slanted. Install the fan motor assembly to the oven cavity with three (3) screws. Install the magnetron with three (3) screws. Re-install the wire leads of the fan duct. Connect the wire leads to the magnetron and the fan motor, referring to the pictorial diagram.
Shaft

6. 7. 8. 9.

Stator Gap Bracket Rotor

Shaft Axis Stator Rotor

These are the positions that should be pinched with pliers.

Table

Center of bracket

Rear view

Side view
20

Quizás también quiera comprar

$4.99

SX-K700 TECHNICS
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

CJ-V51 PIONEER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

GRAND PRIX ELECTRONIC 754 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

SX-PR602 TECHNICS
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EV-S1000E SONY
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

GRAND PRIX ELECTRONIC 780 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

AG7330 PANASONIC
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

MECABLITZ 60 CT4 METZ
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…
>
Parse Time: 0.172 - Number of Queries: 129 - Query Time: 0.042