Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5856 visitantes online.
Productos
Información
Destacado
Inicio >> SHARP >> R-15AT Manual de Servicio
 
 0 artículo(s) en Su carrito 

SHARP R-15AT
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del SHARP R-15AT Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages: English

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
R-15AT

ANTENNA MOTOR REMOVAL
1. Disconnect the oven from the power supply. 2. Remove the one (1) screw holding the base plate cover to the base plate and remove the base plate cover. 3. Disconnect the wire leads from the antenna motor and remove the one (1) screw holding the antenna motor. 4. Remove the antenna motor shaft from the antenna motor. 5. Now, the antenna motor is free.

FAN MOTOR REPLACEMENT
REMOVAL 1. CARRY OUT 3D CHECKS. 2. Remove the one (1) screw holding the noise filter to the chassis support. 3. Release the noise filter from the tab on the fan duct. 4. Disconnect the wire leads from the fan motor. 5. Remove the one (1) screw holding the capacitor holder to the oven cavity rear plate. 6. Remove the one (1) screw holding the fan duct to the oven cavity rear plate. 7. Remove the fan duct from the oven. 8. Remove the fan blade from the fan motor shaft according to the following procedure. 9. Hold the edge of the rotor of the fan motor by using a pair of groove joint pliers. CAUTION: * Make sure that no metal pieces enter the gap between the rotor and the stator of the fan motor because the rotor is easily shaven by pliers and metal pieces may be produced. * Do not touch the pliers to the coil of the fan motor because the coil may be cut or injured. * Do not disfigure the bracket by touching with the pliers. 10. Remove the fan blade from the shaft of the fan motor by pulling and rotating the fan blade with your hand. 11. Now, the fan blade will be free.
Coil Groove joint pliers

CAUTION: * Do not reuse the removed fan blade because the hole (for shaft) may be larger than normal. 12. Remove the two (2) screws holding the fan motor to the fan duct. 13. Now, the fan motor is free. INSTALLATION 1. Install the fan motor to the fan duct with the two (2) screws. 2. Install the fan blade to the fan motor shaft according to the following procedure. 3. Hold the center of the bracket which supports the shaft of the fan motor on the flat table. 4. Install the fan blade to the shaft of fan motor by pushing the fan blade with a small, light weight, ball peen hammer or rubber mallet. CAUTION: * Do not hit the fan blade hard when installing because the bracket may be disfigured. * Make sure that the fan blade rotates smooth after installation. * Make sure that the axis of the shaft is not slanted. 5. Install the fan duct to the oven cavity rear plate with the one (1) screw. 6. Install the capacitor holder to the oven cavity rear plate with the one (1) screw. 7. Install the noise filter to the fan duct and the chassis support with the one (1) screw. 8. Reconnect the wire leads to the fan motor.
Shaft

Stator Gap Bracket Rotor

Shaft Axis Stator Rotor

These are the positions that should be pinched with pliers

Table

Center of bracket

Rear view

Side view

POWER SUPPLY CORD REPLACEMENT
Removal 1. CARRY OUT 3D CHECKS. 2. Remove the one (1) screw holding the green/yellow wire to the cavity rear plate. 3. Disconnect the leads of the power supply cord from the noise filter, referring to the Figure C-3(a). 4. Release the power supply cord from the oven cavity rear plate. 5. Now, the power supply cord is free.
Oven Cavity Back Plate Screw Green/Yelow Wire Brown Wire
L RED WHT

Power Supply Cord

Reinstall 1. Insert the moulding cord stopper of power supply cord into the square hole of the oven cavity rear plate, referring to the Figure C-3(b). 2. Install the earth wire lead of power supply cord to the cavity rear plate with one (1) screw and tight the screw. 3. Connect the brown and blue wire leads of power supply cord to the noise filter correctly, referring to the Pictorial Diagram.
Moulding Cord Stopper

Chassis Support

Power Cord Supply Oven Cavity Rear Plate Square Hole

Bule Wire Noise Filter

N

Figure C-3 (a) Replacement of Power Supply Cord 25

Figure C-3(b). Power Supply Cord Replacement

Quizás también quiera comprar

$4.99

R15AT SHARP
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …
>
Parse Time: 0.34 - Number of Queries: 101 - Query Time: 0.103