PANASONIC PVV4602
Manual de Usuario

Before Using Important Safeguards and Precautions
FOR YOUR SAFETY, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE UNIT
INSTALLATION 1 POWER SOURCE CAUTION Operate only from a power source indicated on the unit or in this manual. If necessary, have your Electric Utility Service Company or Video Products Dealer verify the power source in your home. 2 POLARIZED OR GROUNDING PLUG As a safety feature, this Video product comes with either a polarized power cord plug (one blade is wider than the other), or a three-wire grounding type plug. POLARIZED PLUG CAUTION: This plug will only fit into an outlet one way. If you cannot fully insert the plug, try reversing it. If it still will not fit, have an electrician install the proper wall outlet. Do not defeat the safety feature by tampering with the plug. GROUNDING PLUG CAUTION: This plug will only fit into a three-hole grounding outlet. If necessary, have an electrician install the proper outlet. Do not defeat the safety feature by tampering with the plug. 3 POWER CORD Make sure power cords are routed so that they are not likely to have anything rest on them, roll over them, or be in the way of walking traffic. If an extension cord is used, make sure it also has either a polarized or grounded plug and that the cords can be securely connected. Frayed cords, damaged plugs, and damaged or cracked wire insulation are hazardous and should be replaced by a qualified service technician. Overloaded outlets and extension cords are fire hazards and should be avoided. 4 DO NOT BLOCK VENTILATION HOLES Ventilation openings in the cabinet release heat generated during operation. If they are blocked, heat build-up inside the unit can cause failures that may result in a fire hazard or heat damage to cassettes. For protection, follow these rules: a. Never cover ventilation slots or the unit while in use, or operate the unit when placed on a bed, sofa, rug, or other soft surface. b. Avoid built-in installation, such as a book case or rack, unless proper ventilation is provided. 5 AVOID EXTREMELY HOT LOCATIONS OR SUDDEN TEMPERATURE CHANGES Do not place the unit over or near any kind of heater or radiator, in direct sunlight, inside a closed vehicle, etc.. Do not move the unit suddenly between areas of extreme temperature variation. If the unit is suddenly moved from a cold place to a warm place, moisture may condense in the unit and on the tape. 6 TO AVOID PERSONAL INJURY � Do not place unsecured equipment on a sloping surface. � Do not place this unit on any support that is not firm, level, and adequately strong. The unit could fall causing serious injury to a child or adult and damage to the unit. � An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. � Carefully follow all operating instructions and use the manufacturer's recommended accessories when operating this unit or connecting it to any other equipment. OUTDOOR ANTENNA INSTALLATION 1 SAFE ANTENNA AND CABLE CONNECTION If an outside antenna or cable system is connected to the equipment, be sure the antenna or cable system is grounded so as to provide some protection against built up static charges and voltage surges. Section 810 of the National Electrical Code, ANSI/NFPA 70 (in Canada, part 1 of the Canadian Electrical Code) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode. 2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS An outside antenna system should be located well away it from power lines, electric light or power circuits and where
NEC - NATIONAL
ELECTRICAL CODE GROUND CLAMP ANTENNA LEAD IN WIRE ELECTRIC SERVICE EQUIPMENT ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) GROUND CLAMPS

Connections / Initial Setup (Ready to Play)
Head Cleaning
Old or damaged tapes may clog heads.

Playback / Record on a Tape
Playback a Tape Record on a Tape

Timer Recording
Timer Recording

Location of Controls
Remote Control Buttons
EJECT
Example

� Connections � Initial Setup � Clock Set � Select Channel � Playback � Record � Auto Operation

� Timer Recording � Location of Controls (Remote Control Buttons, Front View of the VCR)

Congratulations
on your new purchase! With proper use, this dependable product will provide years of enjoyment. Please fill in the information below. (Serial number is on tag on back of VCR.) � Date of Purchase � Dealer Purchased From � Dealer Address � Dealer Phone No. � Model No. � Serial No.

Please make all cable or antenna connections before plugging into the AC outlet.
Plugging the VCR Power Cord into an AC wall outlet starts auto channel and clock set.

Video Head Clog Sensor
Screen-right appears during play if clogging is detected. To remove screen, press PLAY.
V I DEO HEADS MAY NEED CLEAN I NG PLEASE I NSERT HEAD CLEAN I NG CASSETTE OR REFER TO MANUAL

Connecting

1 Insert a tape.
VCR TV IN FROM ANT.

1 Insert a tape with a record tab (p. 3). 2 Press CH
or NUMBER keys to select the channel.
� For �LINE� input, see p. 9 of �Advanced Operations� book. � If channel over 100, first press 100 key then the other 2 digits.

1 1) Press PROG/VCR+* button.
2) Press to display program screen.
LIST STOP CH

For ANT./Cable � VCR � TV

� Loose or peeling labels may cause tape jam.

(Ejects tape)

(Illuminates the remote)

LIGHT

1 Connect cable from Antenna/Cable to
VCR�s IN FROM ANT. jack.

1
OUT TO TV

2

GROUNDING CONDUCTORS (NEC SECTION 810-21)

PV-V4602

� Use �dry� type head END : PLAY cleaning cassette only. (Part No. NV-TCL30PT is recommended.) � Follow cleaning tape instructions carefully. Excessive use of tape can shorten head life.

IN from ANT./CABLE

2 Press PLAY to play tape.
� If tape has no rec. tab (p. 3), auto play begins.

2 Connect VCR�s OUT TO TV jack to
TV�s ANT. IN jack with included RF Cable accessory. For DSS/Cable Box � VCR � TV

2
VHF/UHF
TV VCR IN FROM ANT. Cable TV Converter Box

Special Features During Play Forward/Reverse Scene Search � Press FF or REW. � Press PLAY to release.

3 Press SPEED
to select record speed (p. 3).

Built-in Head Cleaner
A clean video head helps produce a clear picture. So, we have equipped your VCR with a built-in, non-chemical head cleaning system that helps prevent clogging of the video heads. Cleaning is performed each time you load or unload a video cassette. � This feature is preventative only, If your video heads are seriously clogged, consider the use

1 Connect your cable box�s OUT jack
to the VCR�s IN FROM ANT. jack with an RF cable. 2 Connect VCR�s OUT TO TV jack to TV�s ANT. IN jack with included RF Cable accessory.
OUT TO TV

Accessories
Remote Control
LSSQ0300

will never come into contact with these power sources if it should happen to fall. When installing an outside antenna, extreme care should be taken to avoid touching power lines, circuits or other power sources as this could be fatal. Because of the hazards involved, antenna installation should be left to a professional. USING THE VIDEO UNIT

Batteries 2 �AA�

1

IN from ANT./CABLE

VHF/UHF

2

WARNING Over tightening �Nut type� RF coaxial cables may damage jacks. Finger tighten only.

If the unit has been in storage or moved to a new location, refer first to the INSTALLATION section of these safeguards. 1 KEEP THIS VIDEO UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND. 2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR STRONG IMPACT, unplug the unit and have it inspected by a qualified service technician before use. 3 DURING AN ELECTRICAL STORM During a lightning storm, whether indoors or outdoors, or before leaving the unit unused for extended periods of time, disconnect all equipment from the power source as well as the antenna and cable system. 4 WHEN THE UNIT IS PLUGGED IN � Never expose the unit to rain or water. DO NOT OPERATE if liquid has been spilled into the unit. Immediately unplug the unit, and have it inspected by a service technician. Fire and shock hazards can result from electrical shorts caused by liquid contact inside. � Never drop or push any object through openings in the unit. Some internal parts carry hazardous voltages and contact can cause electric shock or fire hazard. � Avoid placing the unit directly above or below your TV set as this may cause electrical interference. Keep all magnets away from electronic equipment. 5 USING ACCESSORIES Use only accessories recommended by the manufacturer to avoid risk of fire, shock, or other hazards. 6 CLEANING THE UNIT Unplug the unit. Then, use a clean, dry, chemically untreated cloth to gently remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could overspray, or seep into the unit and cause electrical shock. Any substance such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to greasy, humid, or dusty areas may adversely affect internal parts. SERVICE 1 DO NOT SERVICE THIS PRODUCT YOURSELF If, after carefully following the detailed operating instructions, this Video product does not operate properly, do not attempt to open or remove covers, or make any adjustments not described in the manual. Unplug the unit and contact a qualified service technician. 2 IF REPLACEMENT PARTS ARE REQUIRED Make sure the service technician uses only parts specified by the manufacturer, or those having the same safety characteristics as the original parts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards. 3 HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK After any service or repairs to the unit, request the service technician to conduct a thorough safety check as described in the manufacture�s service literature to ensure that the

RF Coaxial Cable
VJAS0196

of a chemical non-abrasive head cleaning kit or take your VCR to a Service Center.

After search has begun, each additional press of FF or REW changes speed as shown below. [SLP] : Approx. 21X � Approx. 9X [LP] : Approx. 9X � Approx. 7X [SP] : Approx. 7X � Approx. 3X If at 21X, 9X, or 7X speed the picture is interrupted, change speed to 9X, 7X, or 3X.
Notes

4 Press REC
to start recording.
� To edit, press PAUSE/SLOW to pause, and again to resume recording.

1) Set record DATE, Today 13 SAT --:-- --:-- -press to select: TODAY 1~31= one time, SLP 31 1 SELECT START DATE 89 2 6 or DAILY= MON~ FRI, SELECT : SET: END : PROG or WEEKLY= same time 7 SELECT / Selection Order DAILY each week and press . WEEKLY WEEKLY WEEKLY 2) Set remaining items, (SAT) (MON) (SUN) press to select and press to set START/ STOP times, CH(channel) or LINE input (p. 9 of �Advanced Operations� book), and tape speed (p. 3).
DATE START

VCR Plus+

PROG.

POWER
(Turns VCR off/on)

TV (mode)
(Enables TV functions)

VCR (mode)
(Enables VCR functions)

DSS/CABLE mode
(Enables DSS/CABLE functions)

VCR/TV
(For TV or VCR mode)

INPUT
(For LINE or channel)

PLAY (Plays a tape)/ FAST FORWARD/SEARCH
(Fast forwards tape/ forward visual search)

PROGRAM/VCR+
(Displays Timer Program screen)

NUMBER Keys
(Selects channel directly)

REWIND/SEARCH
(Rewinds tape/ reverse visual search) STOP (Stops tape)

Press PROG/VCR+ button to end programming.

ADD/DELETE
(Adds or deletes a channel)

5 Press STOP to stop recording.
One Touch Recording (record in progress)
Press REC repeatedly to set length as follows: 30 min. � 1 hr. � 1:30 � 2:00 � 3:00 � 4:00 � exit. The VCR shuts off at the length set.

3

VCR Plus+ PROG. DT START STOP 13 2 : 00 P 3 : 20P -- -- : -- -- : --- -- : -- -- : --- -- : -- -- : --

LIST CH SPD 02 SLP -- --- --- --

To Enter More Programs Press to select and press to set an unused program. Then repeat step 2. Or, press PROG/VCR+ button to exit.

Remote keys
PLAY, STOP, REW, and FF function as operation keys when menus are displayed.

DISPLAY
(Displays VCR status)

TAPE POSITION
(Locates tape position)

Cleaning the VCR
Use soft, dry cloth or dusting attachment of a vacuum to remove dust from all cabinet vent holes. You may moisten cloth with nonabrasive, antistatic cleaner/ polisher. Caution: Alcohol and various solvents could damage finish.

Doing Initial Setup (Ready to Play)

CANCEL : ADD / DLT SELECT : SET : EXIT : PROG

1 Turn TV on and tune to channel 3. 2 Plug VCR Power Cord into AC wall
outlet. VCR comes on and auto channel and clock set starts.

4 SELECT CONNECTION screen is
displayed. I (If ANT./Cable � VCR � TV connection,) press �VCR press * to select �VCR CABLE/DSS BOX to set.
VCR CLOCK CHANNEL SELECT CONNECTION VCR TV CABLE / DSS BOX VCR TV VCR CABLE / DSS BOX TV SELECT : SET : EXIT : ACT I ON

� Picture interruption may occur with some TVs. � FF and REW search speed may vary depending on current tape position.

SEARCH/ ENTER
(Sets Search System /TV channel)

4 Press POWER off to set the timer Recording. (�TIMER� lights on Multi Function
Display.)
ACTION
(Displays menu)

Specifications
To order accessories, call toll free 1-800-332-5368.
Power Source: 120 V AC, 60 Hz Power Consumption:Power On Approx. 23 W

Loading the Batteries
Video Signal: Video Recording System: Audio Track:

Power Off
Approx. 3.0 W EIA Standard NTSC color 4 rotary heads helical scanning system 1 track (Normal) 2 channel Hi-Fi Audio Sound

� If screen below does not appear, check VCR - TV connection and, if TV is tuned to channel 3, try switching it to channel 4. � To change VCR�s output channel, please refer to �VCR�s Output Channel� in Advanced Operations book (p. 12).
Plugging the AC Power Plug into an AC outlet

TV�, or TV�, and

Still (Freeze) Picture � Press PAUSE/SLOW. � Press PLAY to release. Frame by Frame Picture � Press PAUSE/SLOW in Still mode. � Press PLAY to release. Slow Motion Picture � Hold down PAUSE/SLOW in Still mode. � Press PLAY to release. Notes
� These features work best in SP or SLP mode. � The sound will be muted. � To reduce picture noise, see �Manual Tracking Control� on p. 3. � After VCR is in Still or Slow mode 3 minutes, it auto switches to Stop mode to protect the tape and the video heads.

Record one station, watch another
Press VCR/TV (�VCR� goes out on Multi Function Display), � select channels at TV (recording continues).

COUNTER RESET
(Resets counter to zero)

SPEED
(Changes tape speed)

Review, Replace, or Clear Program (Recording is not in progress)

Cancel a Timer Recording (Recording is in progress)
Press POWER and then STOP within 10 seconds to cancel the Timer Recording. (The TIMER indicator goes out on Multi Function Display.)

PAUSE/SLOW
(Displays still, frame by frame, or slow motion picture)

COMMERCIAL SKIP/ ZERO SEARCH
(Starts Commercial Skip/ Zero Search)

Select channels at VCR (in STOP or PAUSE mode)
Press VCR/TV (�VCR� lights up on Multi Function Display),

a 1) Press PROG/VCR+ button.
2) Press to select LIST.
LIST CH SPD 08 SP 02 SP 10 SP L1 LP

SAP/Hi-Fi
(Selects audio mode for play or record)

RECORD
(Records a program, etc.)

� select channels at VCR.
Notes � Watching one channel and recording another is not possible when using Cable Box or DSS Receiver. � After 5 minutes in Pause mode, VCR stops to protect the tape and the video heads.

b

I (If DSS/Cable Box � VCR � TV connection,)
press to select �CABLE/DSS BOX VCR TV� and press to set.

VCR Plus+ PROG. DT START STOP 7 9 : 00A 12 : 00A 8 10 : 00P 12 : 00P 10 8 : 00P 9 : 00P SU 9 : 00P 10 : 00P CANCEL : ADD / DLT

Press to select desired program.

VOLUME UP/DOWN
(Adjusts TV volume)

CHANNEL UP/DOWN TRACKING/ V-LOCK
(Selects channel/ reduces picture noise during Play and Slow mode)

SELECT : SET : EXIT : PROG

Tuner: Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69 CABLE Channels: Midband A ~ I (14 ~ 22) Superband J ~ W (23 ~ 36) Hyperband AA ~ EEE (37 ~ 64) Lowband A-5 ~ A-1 (95 ~ 99) Special CABLE channel 5A (01) Ultraband 65 ~ 94, 100 ~ 125 Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F) Battery replacement caution Operating Humidity: 10 % ~ 75 % � Do not mix old and new batteries. 2.7 kg (6.0 lbs). � Do not mix alkaline with manganese batteries. Weight: Dimensions: 430 (W) x 98 (H) x 242 (D) mm 16-15/16� (W) x 3-7/8� (H) x Prevent Accidental Tape Erasure 9-9/16� (D) inch

CH AUTO SET PROCEEDING CANCEL : STOP

VCR CLOCK CHANNEL SELECT CONNECTION VCR TV CABLE / DSS BOX VCR TV VCR CABLE / DSS BOX TV

Light Tower Universal Remote Control

c To Replace program...
VCR Plus+ DATE PROG. LIST

1) Press

to display.

7 SUN START 12:00A CH 9:00A STOP 08
TODAY SP

AUTO CLOCK SET PROCEEDING

SELECT : SET : EXIT : ACT I ON

SELECT START DATE

2) Repeat Step 2 (above) to set new programs.

LIGHT button: When pressed, available buttons light and selected mode button (TV, VCR, or DSS CABLE) flashes 5 seconds. If no button is pressed, light goes out in 5 seconds. Also, hold down a button to confirm the selected mode (mode button flashes) in the dark. EJECT button: Press to eject tape. EJECT is not available during record.

CANCEL : STOP

Verify the output channel of your cable box or DSS receiver and press to select and to enter that channel number.
VCR CLOCK CHANNEL SELECT CONNECTION CABLE / DSS BOX VCR TV CABLE / DSS BOX OUTPUT CH CH 0 1 SELECT : SET : EXIT : ACT I ON

3 Press STOP to stop tape.
Press REW or FF in Stop mode to Rewind or Fast Forward tape. Press EJECT on remote, or STOP/EJECT on VCR to eject tape.

SELECT : SET: END : PROG

or
To Clear program...
VCR Plus+ DT START PROG. LIST STOP CH SPD -SP SP LP

If you use a cable box, turn it on and set it to the Public Broadcasting Station (PBS) channel in your time zone. If you use DSS receiver, it must be turned off.

Press ADD/DLT.

Front View of the VCR
REWIND/ SEARCH Cassette Compartment POWER VCR/TV selector FAST FORWARD/ SEARCH PLAY

Break off the tab to prevent recording.

To record again

Note: Designs and specifications are subject to change without notice.

3 Settings are made automatically.
When setup is done, this screen appears.
VCR CLOCK CHANNEL

Features for a Quality Picture
Digital Auto Picture
Automatically controls the video output signal for less noise depending on the tape condition. Record Tab Screw driver Cover the hole with cellophane tape.
R

Safety Precautions

video unit is in safe operating condition.

If �AUTO CLOCK SET IS INCOMPLETE� appears, manually set clock. See below.
VCR CLOCK CHANNEL AUTO CLOCK SET IS INCOMPLETE PLEASE SET CLOCK BY PRESSING ACTION KEY

This video recorder, equipped with HQ (High Quality) system, is compatible with existing VHS equipment. Only use tapes with the mark. Only tapes tested and inspected for use in 2, 4, 6, and 8 hour machines are recommended.

-- -- : -- -- : --8 10 : 00P 12 : 00P 02 10 8 : 00P 9 : 00P 10 SU 9 : 00P 10 : 00P L1 CANCEL : ADD / DLT SELECT : SET : EXIT : PROG

d Press PROG/VCR+ button to end the
program.

9 /29 / 2002 SUN 2 : 20PM
DST : ON SETT I NG : CH 10 AUTO CLOCK SET COMPLETED

Warning: To prevent fire or shock hazard, do not expose this equipment to rain or moisture. CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert. Avertissement: Afin de prévenir tout risque d�incendie ou de chocs électriques, ne pas exposer cet appareil à la pluie ou à une humidité excessive. Attention: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu�au fond.

Auto Operation Functions
Auto Play
Insert a tape � Power comes on � Play starts if no record tab (see p. 3).
Notes

Digital Auto Tracking
Continuously analyzes the signal and adjusts for optimum picture quality.

Manual Tracking Control
(to reduce picture noise) Use during Playback and Slow Motion mode to reduce picture noise. Press CH (TRACKING) / on the remote control or on the VCR until the picture clears up. To return to Auto Tracking, press POWER off, then on again a few seconds later.
R

Auto Rewind

� If you are using a Cable Box, VCR Timer Programming Channel (Step 2 above) must be set to the Cable Box output channel and your Cable Box must be manually set to the desired channel. The Cable Box must be left on. � If a power interruption occurs while programming the timer, the timer program(s) may be canceled. If �TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION� appears on-screen, please reenter the timer programs.

Video Input Connector Audio Input Connector (L/R) Remote CHANNEL UP/ DOWN Sensor RECORD TRACKING/ V-LOCK STOP/EJECT

CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit. This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

Record/Playback Time
Only use tapes with the Tape Speed Setting SP LP mark in this unit.

Manual Clock Set
If Auto Clock Set was incomplete.

bPress

Type of Video Cassette T60 T120 2 Hours T160 2 Hours 40 Minutes 5 Hours 20 Minutes 8 Hours

a Press ACTION on remote to display
CLOCK screen.
VCR CLOCK CHANNEL

to select the month and to set. In the same manner, select and set the date, year, time, and DST (daylight saving time).
VCR CLOCK CHANNEL

Play Fast Forward

� Tape end � Rewind

Play Auto Eject
(Repeat Play must be off)

Play � Tape end � Rewind � Tape ejects if no record tab

Important notes when using DSS receiver
� When recording programs via DSS receiver, DSS receiver must be left on. � When recording programs via an antenna or cable, DSS receiver must be turned off.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

9 /29 / 2002 SUN 2 : 20PM
DST:ON SET COMPLETED SET : START : ACT I ON

� Important Safeguards � Accessories � Head Cleaning � Loading Batteries � Prevent Tape Erasure � Specifications � Record/Playback Time

(Standard Play) 1 Hour (Long Play)

1/ /
R

:
DST:ON

2 Hours 4 Hours

V-Lock Control (to reduce picture jitter)
In Still mode, CH (TRACKING) V-Lock control. / operate as a

FCC Warning: Any unauthorized changes or modifications to this equipment would void the user�s authority to operate.

(Super Long Play) 3 Hours 6 Hours

SLP

-2-

-3-

R

R

R

R

R

SELECT MONTH SELECT : SET : EXIT : ACT I ON

*Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.

*Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.

c Press ACTION to start clock, and go to
step 4 above.

-4-

-5-

-6-

-7-