Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5569 visitantes online.
Productos
Información
Destacado
Inicio >> OTHERS >> PROMMER Manual de Servicio
 
 0 artículo(s) en Su carrito 

OBERHEIM PROMMER
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del OBERHEIM PROMMER Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages: English

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
Programmable power supplies
(Processor schematic page 3) Various voltages required by different types of EPROMs are generated by two programmable power supplies. Half of U36, Q1, Q3, Q4, and Q6 are the active components in the VPP supply. VPP has a range of zero to +27 volts, the output controlled by the reference voltage VPPREF which is produced by a digitally programmed DAC/sample/hold circuit. The supply circuit is current limited and has a voltage gain which is determined by R93 and R94. Digital signal VPPSEL* must be at logic zero to enable the VPP supply. The other half of U36, Q2 and Q5 make up the VCC programmable supply which has an output range of zero to +8 volts. The gain of the VCC circuit is determined by R97 and R99. VCC is also current limited and the circuit is enabled by a logic zero on VCCSEL*.

Battery backup
(Processor schematic page 3) In order to retain the contents of memory at all times, a three volt lithium battery supplies power to the CMOS RAM through R141 and D26 when the main power is off. When the power is on, the +5v supply powers the RAM through D25.

RESET circuitry
(Processor schematic page 5) The PUP (Power UP) circuitry consisting of active components Q10 and U65 disables writing to RAM when power is off. PUP is connected to all 6264 ICs directly and to the 6116 RAM through U41. PUP is also buffered by U41 to provide a RESET* signal for the microprocessor and certain latches. The PUP circuit is very sensitive to sudden changes in the +5 volt power supply. If the ripple on the +5 line is too great, PUP will trigger and RESET* will go low, resetting the microprocessor.

Microprocessor and memory
(Processor schematic page 1) The 68B09 microprocessor chip (U38) along with the firmware contained in EPROMs U51 and U52 control all operations of the Prommer. The main

Prommer Service Manual

8

Quizás también quiera comprar

$4.99

PROMMER OBERHEIM
Diagrama del circuito

Conjunto de diagramas del circuito. Los diagramas serán proporcionados en un archivo PDF. El archiv…

$4.99

PROMMER OBERHEIM
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …
>
Parse Time: 0.207 - Number of Queries: 102 - Query Time: 0.057