SONY PCWAC800STS
Manual de Usuario

Procedure

Check

5

Access Point Function Setup
Procedure
Check

Procedure

Check

Configure the Router functions

7

The Setup Completed window appears.

Configure the Access Point functions

Configure the Router functions of the Router Unit. The basic settings to connect to the Internet are described here. For details about the settings, refer to Help on the Router Unit Setup Page. Specific information required to establish an Internet connection is normally provided by your Internet service provider when making the service contract. You may have to refer to this information when setting up the connection, so have the information at hand.

6
1

Display the Access Point Setup Page

The wireless functions are set in the Wireless Unit. The basic wireless connection settings are described here. For details about the settings, refer to Help the Access Point Setup Page.

Click �Scan�.

1

Click �Easy Setup�.

3 Close the Web browser. Note
Depending on your Internet service provider, you may not be allowed to connect a router type access point to your DSL or cable modem. Refer to the provisions of the contract with your Internet service provider for details.

Note
When you change the wireless settings, the connection to the Access Point is severed. After performing procedure 7, make sure that you perform procedure 8 to reestablish the connection.

1

Click �Easy Setup�.

Access Points are searched for, and any discovered Access Points are displayed in the list.

The Easy Setup Page appears.

Configure the Wireless Communication Settings on the Computer
Procedure
Check

2

Select the Access Point to configure, and click the �Access Point Setup� button.

2

Configure settings.

8
1 2 3 4 5

Configure computer settings

Configure the wireless communication settings on the computer used for the setup to match the Access Point settings.

The Wireless Broadband Router setup wizard starts.

2

Follow the instruction on the screen to complete the setup.

Configure the network name (SSID) and security settings on the computer to match those set in procedure 7.

z
A user name and password input dialog box appears.

Hint

Refer to the instructions of your wireless LAN PC card or Wireless LAN Converter for the setting method.

This completes the configuration.
1 Enter the network name (SSID). The network name (SSID) is an ID that serves to identify the wireless network. You should enter up to 32 characters. Permissible characters are letters, numbers, and symbols. Note
Do not forget the network name (SSID).

3

In the user name text box, enter �admin�, and then click �OK�.

z Hint
� The default password is �admin�. � Leave the �Password� text box blank.

2 Set �Encryption (WEP)� to �Enable�.

Refer to Help for details about Wireless Broadband Router settings.
To display Help, click Access Point Setup Page. or on the Router Unit Setup Page or the

z Hint z
Hint
Encryption (WEP) encodes wireless communications and prevents unauthorized access to the network. The encryption key is the password required for WEP communications on an encrypted network.

If the administrator password is configured in step 2 of the Easy Setup, a user name and password input dialog box appears.
Enter �admin� here. Leave this text box blank.

3 Select �Key Length�. 4 Enter the encryption key, and re-enter it again at �WEP Key (Confirmation)� If you select �40 bits� for the �Key Length�, enter up to five letters, numbers and symbols. If you select �104 bits� for the �Key Length�, enter up to 13 letters, numbers and symbols. Note
Do not forget the encryption key.

Refer to the Read This First supplement for the following information:
� Safety information � Installation � Ethernet cable connection method � Reset to factory defaults � Factory default settings � Status Indicator indications

5 Select the �IEEE 802.11 Mode�.
Enter �admin� here. Enter the administrator password here, as set in step 2 of the Easy Setup.

The Access Point Setup Page appears in a new window.

3

Check that the settings are correct, and click �Execute Setup�.

1 When finished making settings, click �Next�. The Setup Confirmation window appears. 2 Check that the settings are correct, and click �Execute Setup�.
Enter the administrator user name and password to proceed.

When setup is complete, the following screen appears.

When satisfied with the displayed settings, click here.

If you want to modify the settings, click here to return to the previous window.

If you do not want to configure the Access Point, click here.

Proceed to procedure 6 to configure the Access Point.