Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 6043 visitantes online.
Productos
Información
Destacado
Inicio >> AIWA >> NSXA202 Manual de Servicio
 
 0 artículo(s) en Su carrito 

AIWA NSXA202
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del AIWA NSXA202 Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages: English

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
PRACTICAL SERVICE FIGURE

u

FRONT C.B

<TUNER

SECTION>

<DECK

SECTION> 3000Hz * 45Hz Less than 0,35% (W.R.M,S) 30- 60g-cm (FWD, REV) 2- 5g-cm (FWD, REV) 280mV* 3dB (SP OUT 2V) -1,8V * 3.OdB (NORM) Less than 2,0% (NORM, CrOJ Less than 30mV(NORM) Less than 30mV(NORM) More than 60dB (at 125Hz, +1OVU)

-1

SFR201

o+

9

<FM SECTION> IHF Sensitivity: Less than 10/9/9dB (THD 3%) [at 87,5 /98.0 / 108.OMHZ] S/N 50dB Quieting sensitivity : bXS than 35dB [at 98.OMHZ] Signal to noise ratio : Mono : More than 68dB Stereo: More than 66dB [at 98.OMHZ] Distortion : Mono: Less than 1.2% Stereo: Less than 2.0% [at 98.OMHZ] Auto stop Ievel : 25dB * 10dB [at 98.OMHZJ Stereo separation : More than 25dB [at 98.OMHZ] Intermediate frequency : 10.7MHz <MW SECTION> Sensitivity : (S/N 20 dB) Signal to noise ratio :

Tape speed : Wow & flutter: Take-up torque: Back tension : PB output level : REC/PB output level : Distortion (REC/PB) : Noise level (PB) : Noise level (REC/PB) : Erasing ratio:

r
I
m

1

Less than 54/ 52/ 52dB [at 603 /1000 /1404kHzJ Mono : More than 36dB [at 1000kHzJ

PATTERN SIDE
DECK-1 P. HEAD DECK-1 R / P / E HEAD

Stereo: More than 34dB [at 1000kHz] Mono: Less than 1.5% [at 1000kHz] Stereo: Less than 4,0% [at 1000kHz] Auto stop level : 52dB +10/-l5dB [at 1000kHz] Stereo separation: More than 15dB [at 1000kHz] Intermediate frequency : 450kHz Distortion :

o
FWD

10

< DECK

SECTION> 12. PB Sensitivity Check (DECK 1, DECK 2) Settings: Test tape: l�T�A-200 Test point: TP8(Lch), TP9(Rch) Method: Play back the test tape so that the output level at TP8(Lch), TP9(Rch) becomes 110mV* 3,0dB.
q q

9. Tape Speed Adjustment Settings: � Test tape: TTA-100 Test point: TP8(Lch), TP9(Rch) Adjustment location: SFR201 Method: Play back the test tape and adjust SFR201 so that the frequency counter reads 3000Hz * 5Hz,
q q

10. Head Azimuth Adjustment (DECK 1, DECK 2) Settings: Test tape: TI�A-300 �* Test point: TP8(Lch), TP9(Rch) Adjustment location: Head azimuth adjustment screw Method: Play back (FWD) the 10kHz signal of the test tape and adjust screw so that the output becomes maximum. Next, perform on REV PLAY mode.
q q

13. REC/PB Frequency Response Check Settings: Test tape: �ITA-615 (Normal) � Test point: TP8(Lch), TP9(Rch) Input signal : 1kHz / 8kHz (LINE IN) Method : Apply a lkHz signal and REC mode. Then adjust OSC attenuator so that the output level at the TP8(Lch), TP9(Rch) becomes 8-10mV. Record and play back the lkHz and 10kHz signals and check that the output is OdB a 4,0dB.
q q

11. PB Frequency Response Check (DECK 1, DECK 2) Settings: Test tape: lTA-330 Test point :TP8(Lch), TP9(Rch) Method: Play back the 315Hz and 8kHz signals of the test tape and check that the output ratio of the 8kHz signal with respect to that of the 3 15Hz signal is within *5dB.
q q

14. REC/PB Sensitivity Check Settings: � Test tape: �ITA-615 (Normal) Test point : TP8(Lch), TP9(Rch) Input signal : 1kHz (LINE IN) Method: Apply a 1kHz signal and REC mode, Then adjust OSC attenuator so that the output level at the TP8(Lch), TP9(Rch) becomes 80- 100mV, Record and play back the 1kHz signals and check that the output is -0.2 t 3,5dB,
q q

-27-

-28-

Quizás también quiera comprar

$4.99

NSXA202 AIWA
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …
>
Parse Time: 0.164 - Number of Queries: 102 - Query Time: 0.045