Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5213 visitantes online.
Productos
Información
Destacado
Inicio >> JVC >> HR-J260MS Manual de Servicio
 
 0 artículo(s) en Su carrito 

JVC HR-J260MS
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del JVC HR-J260MS Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages:

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
2.3.2 Checking/Adjustment of the Height and Tilt of the Audio Control Head Note: Set a temporary level of the height of the A/C head in advance to make the adjustment easier after the A/C head has been replaced. (See Fig.22-15.) (1) Connect CH-1 of the oscilloscope to AUDIO OUT and CH2 to TP4001 (CTL.P) of the main board assembly and observe the waveforms on both channels in the ALT mode. (2) Play the alignment tape MHPE and adjust it by turning the screws (1), (2) and (3) little by little until the waveform of both the audio output signal and the control pulse reach maximum. The screw (1) and screw (3) are for adjustment of tilt and screw (2) for azimuth.

(6) Then play the alignment tape MHPE-L. (7) Press the channel buttons (+, �) simultaneously during playback to enter the manual tracking mode. (This also brings the tracking to the centre.) (8) Perform the tracking operation and make sure that the FM waveform is at its maximum. (9) If it is not at maximum, loosen the temporarily tightened the screw (4) and turn the A/C head position bit to bring the audio control head to a position, around where the waveform reaches its maximum for the first time. Then tighten the screws (4) and (5).

Toward the capstan Toward the drum
Head base

Head base A/C head position bit PTU94010
Waveform output

Screw (4)

(2)

(1)

To the drum

(3) Audio control head

Screw (5) Audio control head To the capstan

Audio out

Fig. 2-3-6
TP4001 (CTL. P)

Fig. 2-3-5

MHPE played with the standard-width head

MHPE-L played with the triple-width head

2.3.3 Checking/Adjustment of the Audio Control Head Phase (X-Value) (1) Connect the oscilloscope to TP106(PB.FM) of the main board assembly and to TP111(D.FF) of the main board assembly for external sync connection. (2) Play the alignment tape MHPE and observe the FM waveforms. (3) Press the channel buttons (+, �) simultaneously during playback to enter the manual tracking mode. (This also brings tracking to the centre.) (4) Loosen screws (4) and (5) so that the A/C head position bit (PTU94010) is set as indicated in Fig.2-3-6. (5) Turn the A/C head position bit fully toward the capstan. Then turn it back gradually toward the drum and stop on the second peak point position of the FM waveform output level. Then tighten the screw (4) temporarily.

X-value adjustment point To the drum Control head position To the capstan

Maximize

Fig. 2-3-7

2-22

Quizás también quiera comprar

$4.99

HR-J260MS JVC
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …
>
Parse Time: 0.325 - Number of Queries: 101 - Query Time: 0.105