PHILIPS HP2710/12
Manual de Usuario

1. BEFORE USING YOUR NEW PHILIPS RAZOR s Before using, check foil for wear or damage. If foil shows signs of wear or damage, do not use shaver as injury may occur. Do not use until foil has been replaced. s For wet shaving, you may wish to prepare your skin with soap or shaving cream before shaving. s For dry shaving, be certain that your skin is clean. If you have sensitive skin, you may wish to apply talcum powder before and/or after shaving. s When shaving your legs, underarms or bikini line, it is not necessary to press hard to get a close shave. Pressing too hard may cause skin irritation, and razor will not function properly. In addition, do not use deodorant or alcohol based lotions immediately before or after shaving. You may, however, want to use talcum powder. s Clean Razor regularly following MAINTENANCE instructions. s Do not submerge Razor in water for extended periods of time. s To keep Razor waterresistant, keep the rubber sealing ring in battery compartment clean and dry. Occasionally you may want to apply a thin coating of petroleum jelly to ring to keep it from drying out.

2. INSTALLING OR CHANGING BATTERIES s Your new Philips Razor requires 2 �AA� 1.5 volt alkaline or carbon zinc batteries. s Be sure hands and Razor are dry before inserting or replacing batteries. 1. Be certain Razor is in Off position. 2. Hold Razor upside down and remove Battery Compartment cover by grasping cover on both sides. Slide cover away from Razor body (Fig. 1). 3. Insert batteries as shown, making sure the (+) and (-) markings on ends of batteries match those on inside of compartment (Fig. 2). 4. Replace Battery Compartment cover by sliding cover back onto Razor body (Fig. 3). NOTE: Razor will not operate if batteries are inserted incorrectly. s If Razor will not be used on a regular basis, remove batteries.

3. SHAVING LEGS 1. Prepare legs for wet or dry shaving (see BEFORE USING YOUR NEW PHILIPS RAZOR). 2. Turn Razor on (Fig. 4). 3. Hold Razor so that Shaving Head is in full contact with your skin. Shave with smooth, steady strokes, against the direction of hair growth (Fig. 5). s Pressing too hard may cause skin irritation. s Practice is best for optimum results. 4. Turn Razor Off.

4. SHAVING UNDERARMS 1. Prepare underarms and other sensitive areas for wet or dry shaving (see BEFORE USING YOUR NEW PHILIPSRAZOR section). 2. Turn Razor on. 3. Lift your arm until skin under arm stretches slightly. s For shaving other sensitive areas, stretch skin taut with your fingers. 4. Hold Razor so that Shaving Head is in full contact with the skin. Shave with gentle strokes, using light pressure (Fig. 6). s Pressing too hard may

1

2

3

4

5

6

4. SHAVING UNDERARMS (CONT.)
cause skin irritation, and Razor will not function properly. 5. Do not use deodorant or alcohol based lotions immediately before or after shaving. You may, however, want to use talcum powder. 6. Turn Razor Off (Fig. 7).

5. MAINTENANCE/CLEANING INSTRUCTIONS IMPORTANT s It is recommended that you replace your shaving foil once a year. s Switch Razor Off before cleaning. s Never clean, remove, or replace Shaving Head while motor is on. s Do not apply pressure or touch Shaving Head with hard objects as this may dent or damage foil or trimmers. If damage occurs, replace foil. s Check foil regularly. s Replace foil once a year. s Never use a razor with a damaged or broken foil. s For best shaving performance, it is suggested to lightly oil Shaving Head regularly by spreading a drop of mineral oil over the foil and trimmers (Fig. 8). If this does not improve the performance of your razor, it may be time to change foil. s If Razor will not be used on a regular basis, remove batteries. A. AFTER EACH USE After each use, Razor should be quickly cleaned by rinsing under running water or dipping and shaking gently in water. s Never immerse Razor in water while battery compartment is open. IMPORTANT: DO NOT keep Razor submerged in water for a long period of time. B. ONCE A MONTHCLEANING SHAVING HEAD IMPORTANT: DO NOT apply pressure to Shaving Foil. 1. To remove Foil Guard, simultaneously press in small buttons on both sides of Razor on Angled Shaving Head while pulling head up and out (Fig. 9). Rinse under water to remove hairs (Fig. 10). s Hold Shaving Foil by plastic housing only Shaving Foil is very delicate and should not be handled. If foil becomes worn or damaged, replace it. 2. Remove Cutter Block as shown (Fig. 11). Hairs can be removed from Cutter Block by using a soft brush, by lightly blowing out hairs, or running under water (Fig. 12). NOTE: Avoid using brush on Cutter Block as this may cause damage. s Body of Razor and Shaving Head, including Shaving Foil, may be rinsed under running water to remove hairs (Fig. 13). 3. Be sure all parts are dry before reassembling. s Do not use cloth or towel to dry Shaving Foil or Cutter Block; allow to air dry. 4. Replace Cutter Block and Shaving Foil by gently pressing back into position on Shaving Head. s Hold Razor Head by plastic housing only. NOTE: Use cold or lukewarm water. Never use cleaners such as alcohol or nail polish remover.

6. PRODUCT ASSISTANCE s For assistance or the Authorized Norelco Service Location nearest you, call toll free:

1-800-243-7884
s Or visit our Website at www.philipsonline.com. Authorized Norelco Service Location information is available 24 hours a day, 7 days a week.

7

8
OIL

9

10

11

12

13