3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS
3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS
3-2 Attaching the Zoom Lens
1. Loosen the mount ring. 2. Connect the cable connector.
Pin
3-4 Attaching the Microphone (Provided)
1.3. 4. 2.
Connect the provided microphone to the viewfinder. The provided microphone is a phantom microphone.
3. Attach the lens with its pin aligned with the hole in the mount. 4. Tighten the mount ring.
CAUTION: � Be sure to tighten the mount ring completely. Incomplete tightening may result in the lens dropping off or disturbed
1.
4. 3.
1. Loosen the stopper screw on the viewfinder. 2. Attach the microphone to the attachment guide on the viewfinder as illustrated. 3. Confirm that there is no gap between the microphone and
the viewfinder, and then tighten the stopper screw.
Hole
2.
When unplugging the cable connector, first remove the lens itself. Then grasp this portion and pull out.
4. Tighten the screw on the microphone. The microphone
should be firmly attached.
back focus. � Set the GY-DV5000's power switch to �OFF� before the zoom lens is attached or detached.
5. Connect the cable from the microphone to the FRONT
AUDIO IN connector on the camera.
6. Secure
5.
Microphone cable Cable clamp
VF
the microphone cable using the cable clamp provided on the front side of the microphone holder.
MEMO:
3-3 Attaching the Viewfinder
By changing the position of the viewfinder mount base on the camera the viewfinder can be observed with either the left or the right eye. When shipped from the factory, the viewfinder mount base is attached so that the viewfinder is mounted for right eye use. After the viewfinder has been attached, the viewfinder can be slid forward. â� Observing the viewfinder with the left eye Change the mounting position of the viewfinder mount base.
6.
When attaching the viewfinder for use with the left eye, the provided microphone cannot be attached. In this case, use the optional microphone holder KA-A50 and microphones MV-P615U/618U (phantom microphone).
3-5 Attaching the Microphone (Optional)
1.
Screw holes for left eye use
3.
2,4.
1. Loosen the two fastening screws of the viewfinder mount
2. Cap
Fastening screws
KA-A50 Microphone holder
With the optional KA-A50 microphone holder, the optional microphones MV-P615U (phantom microphone) and MV-P618U (phantom microphone) can be used.
base with an hexagon wrench (Provided) and then remove
1.
<Attaching the Microphone Using KA-A50>
4. Cap
HEXAGON WRENCH Mounting guide
the viewfinder mount base (including the sliding securing ring).
2. Remove the cap. 3. Mount the viewfinder mount base (including the sliding
securing ring) at the screw holes for left eye use and tighten the screw with the hexagon wrench (Provided).
1. Secure the microphone holder with 2 screws. 2. Turn the small knob located on the outer side of the
microphone holder counterclockwise to loosen it, and loosen the large knob located on the inner side in the same way. Rotate the large knob fully counterclockwise to open the holder.
Sliding securing ring
5.
1. 4.
Stopper screw
4. Attach the removed cap on the right-eye side.
â� Attaching the Viewfinder
3. Attach the microphone to the microphone holder at the
designated place so that the microphone does not interfere
3.
Viewfinder mount base
4. Set the microphone holder so that the height is level, and
with the cassette cover.
2.
Connector
1. Loosen the stopper screw. 2. Connect the cable connector. 3. Attach the viewfinder with its guide aligned with the shoe. 4. Tighten the stopper screw. 5. Tighten the sliding securing ring.
* Reverse the procedure to remove the viewfinder.
3.
MV-P615U/MV-P618U
tighten the inside and outside knobs to secure the microphone. 5. Connect the microphone cable to the FRONT AUDIO IN connector. � When the microphone is connected to REAR AUDIO IN connector on the rear panel, set the CH-1 or CH-2 AUDIO input selector switch to REAR. 6. Secure the microphone cable using the cable clamp located on the front side of the microphone holder.
Viewfinder
1. 3.
Sliding securing ring
â� Sliding the viewfinder forward
6.
7. Make sure to perform the correct settings for use of a
phantom microphone. � See �FRONT/REAR AUDIO INPUT switch 15.
1. Loosen the sliding securing ring. 2. Slide the viewfinder forward. 3. Tighten the sliding securing ring.
!� on page
CAUTION:
� When the light mounted on the camera is used at the same time, if the microphone in use has a long sound collecting section, the microphone�s shadow may appear in the image.
FRONT AUDIO INPUT Microphone cable
2.
CAUTION: � Set the GY-DV5000�s power switch to �OFF� before the viewfinder is attached or detached.
5.
31
30
