|
Usuarios conectados
Actualmente hay 5900 visitantes online.
|
Productos
|
Información
|
Destacado
|
|
|
|
|
No hay comentarios de productos.
EDITING EN
37
Audio Dubbing
The audio track can be customized only when recorded in the 12-bit and SP modes. ( pg. 26)
� Use the provided remote control.
Insert Editing
You can record a new scene into a previously recorded tape, replacing a section of the original recording with minimal picture distortion at the in and outpoints. The original audio remains unchanged.
� Use the provided remote control. Stereo Microphone
NOTES:
PAUSE START/ STOP REW INSERT STOP
T W
� Before performing the following steps, make sure that �TIME CODE� is set to �ON�. ( pg. 25, 28) � Insert Editing is not possible on a tape recorded in the LP mode or on a blank portion of a tape. � To perform Insert Editing while watching in the television, make connections. ( pg. 17)
PLAY A.DUB
Speaker
1 Play back the tape, locate the Edit-Out point and
press PAUSE (9). Confirm the time code at this point. ( pg. 13)
2 Press REW (3) until the Edit-In point is located,
then press PAUSE (9).
1 Play back the tape to locate the point where editing
will start, then press PAUSE (9). While holding A. DUB (D) on the remote control, press PAUSE (9). The �9D� and �MIC� indicators appear. the microphone.
� To pause dubbing, press PAUSE (9).
3 Press and hold INSERT (I) on the remote control,
then press PAUSE (9). The �9I� indicator and the Time Code (min.:sec.) appear and the camcorder enters Insert-Pause mode.
2
3 Press PLAY (U), then begin �narrating�. Speak into 4 To end Audio Dubbing, press PAUSE (9), then STOP
4 Press START/STOP to begin editing.
� Confirm the insert at the time code you checked in step 1. � To pause editing, press START/STOP. Press it again to resume editing.
5 To end Insert Editing, press START/STOP, then
STOP (8).
(8). To hear the dubbed sound during playback Set �NARRATION� to �ON� or �MIX�. ( pg. 25, 28)
NOTES:
� Program AE with special effects (
pg. 30) can be used to spice up the scenes being edited during Insert Editing.
NOTES:
� Sound is not heard from the speaker during Audio Dubbing. � When editing onto a tape that was recorded at 12-bit, the old and new soundtracks are recorded separately. � If you dub onto a blank space on the tape, the sound may be disrupted. Make sure you only edit recorded areas. � If feedback or howling occurs during TV playback, move the camcorder�s microphone away from the TV, or turn down the TV�s volume. � If you change from 12-bit to 16-bit in mid-recording and then use the tape for Audio Dubbing, it is not effective from the point where 16-bit recording began. � During Audio Dubbing, when the tape moves to scenes recorded in the LP mode, scenes recorded in 16-bit audio or a blank portion, Audio Dubbing stops. � To perform Audio Dubbing while watching on the television, make connections. ( pg. 17) � To perform Audio Dubbing with a video unit connected to the camcorder�s AV connector, first set �S/AV INPUT� to �ON� in VIDEO Menu. ( pg. 25, 28) The �AUX� indication appears instead of �MIC�.
� During Insert Editing, the date and time information changes. � If you perform Insert Editing onto a blank space on the tape, the audio and video may be disrupted. Make sure you only edit recorded areas. � During Insert Editing, when the tape moves to scenes recorded in the LP mode or a blank portion, Insert Editing stops. ( pg. 43)
ADVANCED FEATURES
|
|
|
> |
|