|
Usuarios conectados
Actualmente hay 6042 visitantes y 1 usuarios online.
|
Productos
|
Información
|
Destacado
|
|
|
|
|
No hay comentarios de productos.
Snapshot (For Tape Recording)
This feature lets you record still images that look like photographs onto a tape.
SNAPSHOT MODE SELECTION
� while pressing down the Lock Button e located on the switch. Open the LCD monitor fully or pull out the viewfinder fully. Press the MENU/VOLUME wheel Screen appears. � (CAMERA)�, then press it.
1 Set the Power Switch r to � 2
# in. The Menu
� To remove the shutter sound, �BEEP� on pg. 23. � If Snapshot recording is not possible, �PHOTO� ^ blinks when SNAPSHOT $ is pressed. � If Program AE with special effects ( pg. 16) is engaged, certain modes of Program AE with special effects are disabled during Snapshot recording. In such a case, the icon blinks. � If SNAPSHOT $ is pressed when �DIS� is set to �ON� ( pg. 22), the Stabilizer will be disabled. � During playback as well, all Snapshot modes are available. The shutter sound is not heard. � During Snapshot recording, the image displayed in the viewfinder may be partially missing. However, there is no effect in the recorded image. � When a cable is connected to the AV connector, the shutter sound is not heard from the speaker, however it is recorded onto the tape.
NOTES:
3 Rotate the MENU/VOLUME wheel # to select 4 Rotate the MENU/VOLUME wheel # to select �SNAP MODE�, then press it. 5 Rotate the MENU/VOLUME wheel # to select the desired Snapshot mode, then press it.
Rotate the MENU/VOLUME wheel # to select � RETURN� and press it twice. The Menu Screen closes.
Auto Focus
The camcorder�s Full Range AF system offers continuous shooting ability from close-up (as close as approx. 5 cm (2") to the subject) to infinity. However, correct focus may not be obtainable in the situations listed below (in these cases use manual focusing): � When two subjects overlap in the same scene. � When illumination is low.* � When the subject has no contrast (difference in brightness and darkness), such as a flat, one-color wall, or a clear, blue sky.* � When a dark object is barely visible in the viewfinder.* � When the scene contains minute patterns or identical patterns that are regularly repeated. � When the scene is affected by sunbeams or light reflecting off the surface of a body of water. � When shooting a scene with a high-contrast background.
* The following low-contrast warnings appear blinking: ,, and
FULL Snapshot mode with no frame
PIN-UP Pin-Up mode
FRAME Snapshot mode with frame
There is the sound effect of a shutter closing.
SNAPSHOT RECORDING
1 Press SNAPSHOT $. �PHOTO� ^ appears while
the snapshot is being taken. If you press during Record-Standby . . . ..... �PHOTO� ^ appears and a still image will be recorded for approx. 6 seconds, then the camcorder re-enters the Record-Standby mode. If you press during Recording . . . ..... �PHOTO� ^ appears and a still image will be recorded for approx. 6 seconds, then the normal recording resumes. � Regardless of the Power Switch r position (� � or � �), Snapshot recording takes place using the selected Snapshot mode. Motor Drive Mode Keeping SNAPSHOT $ pressed provides an effect similar to serial photography. (Interval between still images: approx. 1 second)
NOTES:
� If the lens is smeared or blurred, accurate focusing is not possible. Keep the lens clean, wiping with a piece of soft cloth if it gets dirty. When condensation occurs, wipe with a soft cloth or wait for it to dry naturally. � When shooting a subject close to the lens, zoom out first ( pg. 12). If zoomed-in in the auto focus mode, the camcorder may automatically zoom out depending on the distance between the camcorder and the subject. This will not occur when �TELE MACRO� ( pg. 22) is activated.
EN
18 FOR RECORDING
|
|
|
> |
|