PIONEER GM-X362/XH/ES
Manual de Usuario

Before Using This Product
BRIDGEABLE POWER AMPLIFIER AMPLIFICADOR DE POTENCIA EN PUENTE
Thank you for purchasing this PIONEER product. Before attempting operation, be sure to read this manual.

Setting the Unit
WARNING Gain Control
� Always use the special red battery and ground wire [RD-223], which is sold separately. Connect the battery wire directly to the car battery positive terminal (+) and the ground wire to the car body. � Do not touch the amplifier with wet hands. Otherwise you may get an electric shock. Also, do not touch the amplifier when it is wet. � For traffic safety and to maintain safe driving conditions, keep the volume low enough so that you can still hear normal traffic sound. � Check the connections of the power supply and speakers if the fuse of the separately sold battery wire or the amplifier fuse blows. Detect the cause and solve the problem, then replace the fuse with another one of the same size and rating. � To prevent malfunction of the amplifier and speakers, the protective circuit will cut the power supply to the amplifier (sound will stop) when an abnormal condition occurs. In such a case, switch the power to the system OFF and check the connection of the power supply and speakers. Detect the cause and solve the problem. � Contact the dealer if you cannot detect the cause. � To prevent an electric shock or short-circuit during connection and installation, be sure to disconnect the negative (�) terminal of the battery beforehand. � Confirm that no parts are behind the panel when drilling a hole for installation of the amplifier. Be sure to protect all cables and important equipment such as fuel lines, brake lines and the electrical wiring from damage.

Power Indicator
The power indicator lights when the power is switched on.

If the sound level is too low, even when the volume of the car stereo used along with this power amplifier is turned up, turn gain control on the front of the power amplifier clockwise. If the sound distorts when the volume is turned up, turn the gain control counter-clockwise.
� When using with an RCA equipped car stereo (standard output of 500 mV), set to the NORMAL position. When using with an RCA equipped Pioneer car stereo with max. output of 4 V or more, adjust level to match the car stereo output level. � If you hear too much noise when using the speaker input terminals, turn the gain control counter-clockwise.

In case of trouble
When the unit does not operate properly, contact your dealer or the nearest authorized PIONEER Service Station.

BFC (Beat Frequency Control) Switch
If you hear a beat while listening to an AM broadcast with your car stereo, change the BFC switch using a small standard tip screwdriver.

Owner�s Manual

GM-X362
Manual del Propietario

PIONEER CORPORATION
4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN
PIONEER ELECTRONICS (USA) INC. P.O. Box 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: (0) 3/570.05.11 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia TEL: (03) 9586-6300 PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: (905) 479-4411 PIONEER ELECTRONICS DE MEXICO, S.A. de C.V. San Lorenzo 1009 3er. Piso Desp. 302 Col. Del Valle Mexico, D.F. C.P. 03100 TEL: 5-688-52-90

LPF (Low-Pass Filter) Select Switch
Set the LPF select switch as follows according to the type of speaker that is connected to the speaker output connector and the car stereo system:
Published by Pioneer Corporation. Copyright © 2001 by Pioneer Corporation. All rights reserved. Publicado por Pioneer Corporation. Copyright © 2001 Pioneer Corporation. Todos los derechos reservados. Printed in China Impreso na China

LPF Select Switch
LPF (left) OFF (right)

Audio frequency range to be output
Very Low Frequency range Full range

Speaker Type
Subwoofer Full range

Remarks
Connect a subwoofer.

<KYMFX/01I00000>

<HZR0003-A> ES