PIONEER GM-D7400M/XS/ES
Manual de Usuario

Connecting the Unit
Connecting the Speaker Output Terminals
� Use a 10 AWG to 16 AWG wire for the speaker wire.

ENGLISH
7 Connections when using the speaker input

Installation
CAUTION
� Do not install in: �Places where it could injure the driver or passengers if the vehicle stops suddenly. �Places where it may interfere with the driver, such as on the floor in front of the driver�s seat. � Make sure that wires are not caught in the sliding mechanism of the seats, resulting in a short-circuit. � Confirm that no parts are behind the panel when drilling a hole for installation of the amplifier. Protect all cables and important equipment such as fuel lines, brake lines and electrical wiring from damage. � Install tapping screws in such a way that the screw tip does not touch any wire. This is important to prevent wires from being cut by vibration of the car, which can result in fire. � DO NOT allow amplifier to come into contact with liquids due to, for example, the location where the amplifier is installed. Electrical shock could result. Also, amplifier and speaker damage, smoke, and overheating could result from contact with liquids. In addition, the amplifier surface and the surface of any attached speakers could become hot to the touch and minor burns could result. � To ensure proper installation, use the supplied parts in the manner specified. If any parts other than the supplied ones are used, they may damage internal parts of the amplifier, or they may become loose causing the amplifier to shut down. � Never replace the fuse with one of greater value or rating than the original fuse. Use of an improper fuse could result in overheating and smoke and could cause damage to the product and injury including burns.

ENGLISH
CAUTION: To prevent malfunction and/or injury
� To ensure proper heat dissipation of the amplifier, be sure of the following during installation. �Allow adequate space above the amplifier for proper ventilation. �Do not cover the amplifier with a floor mat or carpet. � DO NOT allow amplifier to come into contact with liquids due to, for example, the location where the amplifier is installed. Electrical shock could result. Also, amplifier and speaker damage, smoke, and overheating could result from contact with liquids. In addition, the amplifier surface and the surface of any attached speakers could become hot to the touch and minor burns could result. Do not install the amplifier on unstable places such as the spare tire board. The best location for installation differs with the car model and installation location. Secure the amplifier at a sufficiently rigid location. Make temporary connections first and check that the amplifier and the system operate properly. After installing the amplifier, confirm that the spare tire, jack and tools can be easily removed.

Specifications

ENGLISH

Example of installation on the floor mat or on the chassis
1. Place the amplifier where it is to be installed. Insert the supplied tapping screws (4 mm � 18 mm) into the screw holes. Push on the screws with a screwdriver so they make marks where the installation holes are to be located. 2. Drill 2.5 mm diameter holes at the point marked, and install the amplifier, either on the carpet or directly to the chassis.
Tapping screw (4 mm � 30 mm)

Power source............................................................................................................ 14.4 V DC (10.8 V to 15.1 V allowable) Grounding system ............................................................................................................................................ Negative type Current consumption ........................................................................................................ 17.0 A (at continuous power, 4 �) Average current drawn* .............................................................................................................. 5.0A (4 � for one channel) 10.0 A (2 � for one channel) Fuse .......................................................................................................................................................................... 25 A � 2 Dimensions .......................................................................................................... 225 mm (W) � 56 mm (H) � 200 mm (D) (Terminals not included) Weight ...................................................................................................................... 2.6 kg (Leads for wiring not included) Maximum power output ................................................................................................ 400 W � 1 (4 �) / 800 W � 1 (2 �) Continuous power (14.4 V) .................................................................... 4 �, 20 Hz to 240 Hz, 1.0 % THD, 200 W � 1 2 �, 50 Hz, 1.0 % THD, 400 W � 1 Load impedance .......................................................................................................................... 4 � (2 � to 8 � allowable) Frequency response ............................................................................................................ 10 Hz to 240 Hz (+0 dB, �3 dB) Signal-to-noise ratio ........................................................................................................................ 80 dB (IEC-A network) Distortion .............................................................................................................................................. 0.3% (10 W, 100 Hz) Low pass filter .............................................................................................................. Cut off frequency: 40 Hz to 240 Hz Cut off slope: �12 dB/oct Bass Boost .................................................................................................................................................. Frequency: 50 Hz Level: 0 dB/6 dB/12 dB Gain control ...................................................................................................................................... RCA: 200 mV to 6.5 V Speaker: 0.8 V to 26 V Maximum input level / impedance ........................................................................................................ RCA: 6.5 V / 22 k� Speaker: 26 V / 90 k�

1. Expose the end of the speaker wires using nippers or a cutter by about 10 mm to 12 mm.

Car Stereo

Speaker output

10 mm to 12 mm

2. Connect the speaker wires to the speaker output terminals.
� Fix the speaker wires securely with the terminal screws. Terminal screws

White: Black: Left + Left �

Black: Red: Right � Right +

� � � �

Speaker input wire with RCA pin cord

Note:
� Specifications and the design are subject to possible modification without notice due to improvements.

Speaker output terminal

Speaker wire

To RCA input jack of this unit.

*Average current drawn
Floor mat or chassis � The average current drawn is nearly the maximum current drawn by this unit when an audio signal is input. Use this value when working out total current drawn by multiple power amplifiers.

Connecting the Speaker Wires Using the Speaker Input
Connect the car stereo speaker output wires to the amplifier using the supplied speaker input wire with RCA pin cord.
� Slide the input switch to the left (SP).

Drill a 2.5 mm diameter hole

Connect the speaker leads according to the figures shown below.

Subwoofer