No hay comentarios de productos.
USER�S GUIDE 2597
To test the alarm In the Alarm Mode, hold down D to sound the alarm. To turn Alarms 2 through 5 on and off
One-time alarm on indicator
About the Auto Light Switch
Turning on the auto light switch causes the backlight to turn on for about one second, whenever you position your wrist as described below in any mode. Moving the watch to a position that is parallel to the ground and then tilting it towards you more than 40 degrees causes the backlight to turn on.
1. In the Alarm Mode, use D to select a one-time alarm (alarm number 2 through 5). 2. Press A to toggle the displayed alarm on and off. � Turning on a one-time alarm (2 through 5) displays the one-time alarm on indicator (ALM) on its screen. � The one-time alarm on indicator is displayed in all modes. � If any alarm is on, the alarm on indicator is shown on the display in all modes.
Parallel to ground
More than 40°
To select the operation of Alarm1 1 1. In the Alarm Mode, use D to select Alarm1. 2. Press A to cycle through the available settings in the sequence shown below.
SNZ indicator and one-time alarm on indicator ALM One-time alarm on SNZ ALM Snooze alarm on Alarm off
� The applicable alarm on indicator (ALM or SNZ ALM) is displayed in all modes when an alarm is turned on. � The SNZ indicator flashes during the 5-minute intervals between alarms. � Displaying the Alarm1 setting screen while the snooze alarm is turned on automatically turns off the snooze alarm (making Alarm1 a one-time alarm).
Warning! � Always make sure you are in a safe place whenever you are reading the display of the watch using the auto light switch. Be especially careful when running or engaged in any other activity that can result in accident or injury. Also take care that sudden illumination by the auto light switch does not surprise or distract others around you. � When you are wearing the watch, make sure that its auto light switch is turned off before riding on a bicycle or operating a motorcycle or any other motor vehicle. Sudden and unintended operation of the auto light switch can create a distraction, which can result in a traffic accident and serious personal injury.
To turn the hourly time signal on and off 1. In the Alarm Mode, use D to select the Hourly Time Hourly time signal Signal. on indicator 2. Press A to toggle it on and off. � Turning on the Hourly Time Signal displays the hourly time signal on indicator (SIG) on its screen. � The hourly time signal on indicator is displayed in all modes.
To turn the auto light switch on and off In the Timekeeping Mode, hold down D for about two seconds to toggle the auto light switch on (AUTO EL displayed) and off (AUTO EL not displayed). � The auto light switch on indicator (AUTO EL) is on the display in all modes while the auto light switch is turned on.
Battery
This watch is equipped with a solar cell and a rechargeable battery (secondary battery) that is charged by the electrical power produced by the solar cell. The illustration shown below shows how you should position the watch for charging. Example: Orient the watch so its Solar cell face is pointing at a light source.
Stopwatch
The stopwatch lets you measure elapsed time, split times, and two finishes. � The display range of the stopwatch is 99 hours, 59 minutes, 59.99 seconds. � The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it. � The stopwatch measurement operation continues even if you exit the Stopwatch Mode. � Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement. � All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C.
� Note that charging efficiency drops when any part of the solar cell is blocked by clothing, etc. � The illustration shows how to position a watch with a resin band. Important! � Storing the watch for long periods in an area where there is no light or wearing it in such a way that it is blocked from exposure to light can cause rechargeable battery power to run down. Be sure that the watch is normally exposed to bright light whenever possible. � This watch employs a solar cell that converts light into electricity, which charges a built-in rechargeable battery. Normally, the rechargeable battery should not need replacement, but after very long use over a number of years, the rechargeable battery may lose its ability to achieve a full charge. Should you notice problems with getting the rechargeable battery to a full charge, contact your dealer or CASIO distributor about having the rechargeable battery replaced. � The rechargeable battery should be replaced with a CASIO-specified CTL1616 battery only. Other rechargeable batteries can cause damage to the watch. � All data stored in memory is deleted, and the current time and all other settings return to their initial factory defaults whenever battery power drops to Level 5 and when you have the battery replaced. � Turn on the watch�s Power Saving function and keep it in an area normally exposed to bright light when storing it for long periods. This helps to keep the rechargeable battery from going dead.
Minutes
1/100 Second
Hours
Seconds
To measure times with the stopwatch
Elapsed Time D
Start �D Stop �D Re-start �D Stop �A Clear
Split Time D
Start �A Split
(SPdisplayed)
�A Split release
�D Stop
�A Clear
Two Finishes D
Start �A Split
First runner finishes. Display time of first runner.
Battery Power Indicator
�
D
Stop
Second runner finishes.
�A Split release
Display time of second runner.
�A Clear
The battery power indicator on the display shows you the current status of the rechargeable battery�s power. Level
Battery power indicator
1 2
Battery Power Indicator
Function Status All functions enabled. All functions enabled. All functions enabled.
Dual Time
The Dual Time Mode lets you keep track of time in a different time zone. � The seconds count of the Dual Time is synchronized with the seconds count of the Timekeeping Mode.
3 4
Beeper tone, backlight, display, and buttons are (Charge Soon Alert) disabled. All functions, including timekeeping, are disabled.
To set the Dual Time
Timekeeping Mode time
5 1. Press C to enter the Dual Time Mode. 2. Use A and D to set the Dual Time Mode time. � Each press of D increases the time setting in 30-minute increments. � Pressing A sets the Dual Time Mode to the same time as the Timekeeping Mode. � The flashing
indicator at Level 4 tells you that battery power is very low, and that
Dual time (Hours : Minutes Seconds)
Backlight
Auto light switch on indicator
The backlight uses an EL (electro-luminescent) panel that causes the entire display to glow for easy reading in the dark. The watch�s auto light switch automatically turns on the backlight when you angle the watch towards your face. � The auto light switch must be turned on (indicated by the auto light switch on indicator) for it to operate. � See �Backlight Precautions� for other important information about using the backlight.
exposure to bright light for charging is required as soon as possible. � At Level 5, all functions are disabled and settings return to their initial factory defaults. Functions are enabled once again after the rechargeable battery is charged, but you need to set the time, date, and all other settings after the battery is recharged to Level 3 from Level 5. Though the time appears on the display after the battery is charged to Level 4, you will not be able to change the time setting until the battery reaches Level 3. � Leaving the watch in direct sunlight or some other very strong light source can cause the battery power indicator to temporarily show a reading that is higher than the actual battery level. The correct battery power indicator should appear after a few minutes. � If you use the backlight or any of the alarm functions a number of times during a short period, RECOVER appears on the display and the following operations become disabled until battery power recovers. Backlight Beeper tone After some time, battery power will recover and RECOVER will disappear, indicating that the above functions are enabled again.
To turn on the backlight manually In any mode, press B to illuminate the display for about one second. � The above operation turns on the backlight regardless of the current auto light switch setting.
2
