URANIA EA0601
Manual de Usuario

GB
a pipe through the refrigerator's rear panel and into a collection container on the cooling unit, where the water evaporates by itself (fig 7). Should the frost layer become very thick, there is a danger of the collection basin overflowing. In this case the water should be absorbed by a cloth placed under the ribs. The water in the freezer compartment should also be absorbed by a cloth. Following defrosting, the refrigerator should be wiped dry with a cloth, reconnected and the food returned. However, you should wait until the following day before freezing ice cubes.

Figure 6.

6. Ice cubes
Fill the ice tray to 4/5 with drinking water, and place the ice tray on the ice-tray shelf. Wipe off any excess water to prevent the ice tray from freezing to the surface. To speed up the making of ice cubes, turn the thermostat to position �MAX� for a short while. Remember to turn the dial to its normal setting when the ice cubes are frozen. To remove the cubes from the ice tray, hold it under running water. The ice cubes can now be taken out easily.

Figure 7.

7. Useful suggestion
Do not overfill the appliance. It is advisable to leave some space between the products in the cabinet to ensure efficient and even cooling. If the shelves are packed too tightly there may be unacceptable temperature variations.

9. Changing the lightbulb (If available)
If the lightbulb needs changing, pull out the plug and proceed as follows: Press the metal reflector to one side and draw the lamp covering backwards. Replace the bulb and push the covering back into place. A new max. 10-watt bulb can be obtained at any service shop.

Frost will gradually form on the cooling surfaces and it must not be allowed to become too thick since it acts as an insulator and interferes with the cooling. Fuzzy logic and times switch defrosting (fig. 4) This frost-formation is kept back by the FUZZY LOGIC system built into the appliance by switching off the unit for two hours in every 24 hours. The frost will melt and the defrost water will run through the drain tube from the drip channel into an evaporating vessel located at the bottom rear of the refrigerator at all models. (Fig 7) The defrost water will evaporate automatically into the circulating air and the vessel will not need emptying manually. Semi-automatic defrosting (fig. 5) A semi-automatic defrosting model device can be identified by the push -button in the centre of the thermostat dial. To defrost, push in the button in the centre of the thermostat dial but do not turn the dial to another position-leave it at its usual setting. Close the door. The defrost button will stay in and the cooling unit will remain switched off until the frost has melted. The defrost button will then automatically spring out to its normal position and the refrigerator will start work again. The time taken to defrost will depend on the amount of frost to be removed and the room temperature. If we want to switch off the unit, turn the thermostat knob to "0", disconnect the refrigerator from the electricity supply and leave the cabinet door open. After defrosting the cabinet interior should be wiped out with a clean, damp cloth. Automatic defrosting (fig.6) When operating normally, the cooling ribs in the normal compartment defrost automatically. In the case of increased air humidity, frost may form on the cooling ribs. Should the frost layer attain a thickness of approximately 3 mm, the refrigerator must be defrosted to avoid impairing the performance level. Even if this is not the case, the (** and ***) freezer compartment must be defrosted on a regular basis following heavy ice formation every 2-3 months. This is carried out as follows: Set the thermostat at �0�, disconnect at the mains, remove food and ice dish and leave the doors open. Do not expose the refrigerator to external heat and do not attempt to scratch away the frost with sharp objects. The drained water runs in a groove and from there continues along

8. Defrosting, cleaning and maintenance

10. Reversing the door hang, (Fig. 8)

The direction the door opens can be transferred from one side to the other by carrying out the following steps: disconnect at the mains lay the refrigerator down carefully on its back remove the lower hinge � and detach the door remove the two upper left-hand screws and detach the covering plate � by pulling it forward detach the upper hinge and mount it on the opposite side remove the hinge bolt and screw it in from below insert the covering plate in the upper right-hand corner by pushing it in and secure it with the two screws position the door on the upper hinge bolt and mount the lower hinge ensure the door can move freely and the seal is correctly positioned.

Figure 8.

11. Replacing the decorative door panel, (Fig. 9-11)
Remove the two screws (1) from the upper hinge of the door. Pull the door together with the hinge away from the housing and up off the lower hinge bolt (2-3).

6