CAD E350
Manual del propietario

Equitek E-350 Frequency and Polar Response

A Special Note About Batteries

The high quality rechargeable batteries used in the Equitek E-350 may either be Nickel Cadmium or Nickel Metal Hydride. They were selected to provide long life with virtually no maintenance and have a number of properties that make them superior to most commonly available rechargeable "9 volt" batteries:

Cardioid

1) Higher output voltage 2) Lower self discharge rate 3) High immunity to overcharging

Figure 8

If the E-350 is operated with a 48 volt phantom power supply it is unlikely they will ever need to be recharged, even if the microphone is unused for months. If it should ever become necessary to replace the batteries or if you simply want a spare set, we suggest that you buy replacements from us. This is not because we are trying to sell batteries, but because we want you to continue to realize the maximum performance capability of your Equitek microphone. Contact the CAD sales department to purchase replacement or additional batteries.

Re-stringing the elastic cords.

Follow the instructions below if the elastic cords are removed and need to be remounted: For the large circular ring use the elastic cord that is formed in a loop. 1) Using the diagram in Figure 4, start by placing the cord in slot #1. Position the metal clip on the underside of the ring at this position. 2) Using a "wrapping" motion, stretch the cord and use the number guide to install the cord. 3) When complete, the elastic should look like the diagram in Figure 5. 4) Adjust the elastic so that there is nearly equal tension on the individual segments. For the smaller "C" shaped ring use the short elastic cord that has a small loop at each end. 1) Look at the diagram in Figure 6 and attach the elastic cord as shown 2) When complete the prongs of the triangular bracket should point towards the large ring.
POSITION METAL CLIP UNDER RING HERE

Omnidirectional

The CAD ZM-1G is a full elastic suspension system for shock isolating all CAD Equitek cylindrical multi-pattern microphones. The ZM-1G eliminates mechanical shock interference that is transmitted through the microphone stand by footsteps, machinery, or other vibration sources. The ZM-1G also incorporates a built in swivel for ease of microphone positioning. The ZM-1G attaches to microphone stands with a standard 5/8" x 27 thread.

ZM-1G Equitek shock mount Description

Mounting a microphone in the ZM-1G
Unscrew the small knurled adapter and rubber ring from the large knurled knob as shown in Figure 1. Screw the adapter and ring snugly into the bottom of the microphone as shown in Figure 2. Slide the microphone into the mount and screw the knurled knob back into the adapter as shown in Figure 3. Make certain that the microphone is positioned as shown with the microphone connector centered in the opening of the metal ring. An XLR connector that is inserted into the microphone will not touch the metal frame of the ZM-1G if the microphone is positioned properly. The elastic cords in the larger ring should be positioned so that they fall in the name band area in the middle of the microphone.

Figure 4

Figure 5

Figure 6

TWO-YEAR LIMITED WARRANTY
CTI Audio, Inc. (�CAD�) hereby warrants that this product will be free of defects in material and workmanship for a period of two years from the date of purchase. In the unlikely event a defect occurs CAD will, at its option, either repair or replace with a new unit of equal or greater value. You should retain proof of purchase to validate the purchase date and return it with any warranty claim. Return warranty claims carefully packed, insured and prepaid to the Service Department at the address listed below. This warranty excludes exterior finish or appearance, damage from abuse, misuse of the product, use contrary to CAD�s instructions or unauthorized repair. All implied warranties or merchantability or fitness for a particular purpose are hereby disclaimed and CAD hereby disclaims liability for incidental, special or consequential damages resulting from the use or unavailability of this product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above exclusions and limitations may not apply to you. Note: No other warranty, written or oral is authorized by CTI Audio, Inc.

Figure 1

Figure 2

Figure 3

A Division of CTI Audio, Inc. * 341 Harbor St. * Conneaut, OH 44030 * (440) 593-1111 * Fax (440) 593-5395 60%