2. DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY
0 qa
Caution
qg Discharging the capacitor
3
B A A
9
b
Short jig (1k�/1W) FL11800 Hole of Hole of terminal terminal
3 1 3 1 2
qd
A B
6 qf
D
qs 7 8
1 Slide the eject knob in the direction of the arrow a. 2 Open the cassette lid. 3 Screw (M1.7x4) (Black) 4 2 5 4 Open the jack cover. 5 Screw (M1.7x4) (Black) 6 Open the shoe cover. 7 Screw (M1.7x4) (Black) 8 TB cabinet assembly 9 Screw (M1.7x4) (Black) (Silver) 0 Screw (M1.7x4) (Black) (Silver) qa Two screws (M1.7x4) (Black) qs Two claws qd Remove the TU cabinet assembly in the direction of the arrow b. qf Microphone (4P) 2
C A B A
1 Screw (M1.4x2.5) (Black) 2 Three screws (M1.7x4) (Black) 3 Remove the cabinet (B) assembly.
1 Open the LCD panel. 2 Screw (M1.7x4) (Black) (Silver) 3 Three screws (M1.7x2.5) (Silver) 1 2
Three claws
A
A
3
A
a
1
A
Screw M1.7x4 3-087-376-01
B
Screw M1.7x4 3-056-030-91
1 Unlock by pressing the switch in the deep end of the hole. 2 Open the cabinet (R) assembly in the direction of the arrow rotate 45 °. 3 FP-164 flexible board (80P) 1 Open the grip in the direction of the arrow a. 2 Remove the belt in the direction of the arrow b. 3 Remove the belt assembly in the direction of the arrow c. 4 Two tapping screw (M1.7x3.5) (Silver) 5 Plate 6 Belt fixed plate (rear) 7 Grip belt (PC)
C
Screw M1.4x2.5 3-086-368-11
D
Screw M1.7x2.5 3-989-735-01
1 FP-JG9 flexible board (16P) 2 Remove the FP-JG9 flexible board. 3 3 Open the cassette lid. 4 Screw (M1.7x4) (Black) 5 Screw (M1.7x4) (Black) 6 Claw 7 Remove the control switch block (PS11800) in the direction of the arrow. 8 Eject knob
B
Hinge section (See page 2-3)
E
Screw M1.7x2.5 3-084-817-11
F
Tapping screw M1.7x3.5 3-078-890-01
1 7 2
G
Screw M1.7x4 3-084-817-31
H
Screw M1.4x1.5 3-062-214-01
6
G
4
c
8 6 2 1 5 4 HELP 01 7 3 23
I
Tapping screw M1.7x5 3-080-204-21 Silver
J
Tapping screw M1.7x3.5 3-080-204-01 Black
F
a
b
1 Open the cabinet (R) assembly in the direction
G
5
1
of the arrow. 2 FP-168 flexible board (39P)
4
B
2 3 1 FP-170 flexible board (10P) 2 Screw (M1.4x1.5) (Silver) 3 Claw 4 Remove the cabinet (battery) in thedirection of the arrow. 1 Slide the battery lid in the direction of the arrow a, and open it in the direction of the arrow b. 2 Two screws (M1.7x2.5) (Black) Screw (M1.7x2.5) (Black) 3
2 1
Two screws (M1.7x4) (Silver) 4 Tapping screw (M1.7x3.5) (Silver) 5 6 Screw (M1.7x2.5) (Black) a
1
3 5
E
A Strob section
(See page 2-3)
4
a b
1 1 Claw 2 Remove the front block assembly in the direction of the arrow. 3 FP-169 flexible board (20P) 1 Close the cassette lid in the direction
F
6 2
E E
b
1
H
2
of the arrow a. 2 Open the cabinet (G) assembly in the direction of the arrow. b
