|
Usuarios conectados
Actualmente hay 5682 visitantes y 20 usuarios online.
|
Productos
|
Información
|
Destacado
|
|
|
|
|
No hay comentarios de productos.
WINDOW REQUIREMENTS
� Hot sun rays hitting the outside surface of the cabinet will create considerable heat load. If the outside of the cabinet is exposed to direct sunlight, consider building an awning to shade the cabinet 22 to 42-1/8� while providing ample area for the heated air to be exhausted from the condenser (both sides) and the top. This unit is designed for installation in standard double hung windows. NOTE The unit may also be installed �through the wall�. You should, however, observe standard carpentry practices and frame the opening without violating local ordinances.
CHASSIS INSTALLATION INTO THE CABINET
1 Slide the chassis into the cabinet. 2 Reinstall the cabinet screws.
Secure the cabinet to chassis by using screws (from rear cabinet).
°F
hr
TEMP/TIME R
TIMER
SET
OPERATION
COOL FAN HIGH MED LOW FAN SPEED MODE
SET/ CANCEL
OFF/ON
AIR SWING
ECONOM
Y
Wirel
Remot e Cont r ol
ess
INSTALLATION PROCEDURES
1 Remove the rear cabinet
1515 /16� (min)
INSTALLATION OF THE FRONT GRILLE Depending upon the location of the AC outlet, route the AC cord to either the left or right side while installing the front grille.
COOL FAN HIGH MED LOW FAN SPEED MODE AIR SWING
screws and save for later use.
2 Slide the chassis out from the
cabinet.
COOL FAN MODE
HIGH FAN SPEED LOW
MED
°F hr
TEMP/TIMER
TIMER
SET
OPERATION
SET/ CANCEL
OFF/ON
AIR SWING
ECONOMY
Remote Co ntrol
Wireles s
HOW TO ASSEMBLE THE EXPANDABLE PANELS
Top angle Top sealing ribbon (To be attached to the top angle) Type B screws Expandable panel
°F
hr
TEMP/TIM
ER
TIMER
SET
OPERATION
SET/ CANCEL
OFF/ON
ECONOM
Y
Remote
Wirel ess Control
This figure shows the AC cord routed to the left side. 1 Place the front grille on the Side sealing ribbon (To be attached to the expandable panel) Type C screws
cabinet first.
2 Secure the front grille to the
°F
MED FAN SPEED LOW MODE
TIMER
TEMP/TIME R SET
OPERATIO N
hr
main chassis using screw provided. INSERT THE Attach the (part no. CZ-SF6P) to the frame.
COOL FAN
AIR SWING
HIGH
Remote Co ntro
Wirel
SET/ CANCEL
OFF/ON
ECONOM
Y
ess l
NOTE This procedure applies to left and right of assembling expandable panel.
� Attach the top angle to the cabinet using screw type B (3 pcs). � Insert expandable panels to cabinet sides as shown. � Secure the first fold of expansion panel to cabinet using screw type C (3 each). CABINET INSTALLATION
1 Cut the �Sealing Ribbon� to the
Slot in the and the frame (part no. CZ-SFW6P) to the front grille.
proper length, and attach it along the bottom edge of the bottom window sash.
2 To prevent condensation water
Window sash sealing ribbon
COOL
FAN
HIGH MED LOW
MODE
°F
TIMER
TEMP/TIME R SET
OPERATION
hr
SET/ CANCEL
OFF/ON
AIR SWING
ECONOMY
FAN SPEED
Wirele
R e m o t e Co n tro
ss l
from dripping inside, the cabinet should be installed level or very slightly tilted to the outside.
3 Secure the cabinet using screws. Type A screw Type B screws Window sill Type A screws Inside of sash Top angle Expandable panel Window sash foam seal Outside of sash Window sash Sealing ribbon
The and the frame can be obtained separately from your nearest servicenter. INSERT THE AIR FILTER
Attach the air filter to the intake grille
°F
COOL FAN MODE LOW
hr
TEMP/TIME
R
AIR SWING
HIGH MED FAN SPEED
Remote
Wirele ss Control
SET/ CANCEL
SET
TIMER
OPERATION
OFF/ON
ECONOMY
PLACE FRONT INTAKE GRILLE OVER THE FRONT GRILLE Slide the front intake grille slightly to the right to reattach the tabs and then push it down to close tight.
� Expand the expandable panel fully into the grooves of the window frame, secure the expandable panel, left, right and top mounting frames to the bottom of the window sash using 4 screws type A and 2 screws type B. � Secure the cabinet using wood screws type A. � Cut the window sash foam seal to the proper size and seal the opening between the top of the inside window sash and the outside window sash. Note : If a gap exists between the unit and window sash, you may use �Sealer� supplied with the installation kit for a better seal.
°F
HIGH MED LOW
TIMER
TEMP/TIME R SET
OPERATION
hr
SET/ CANCEL
MODE AIR SWING
OFF/ON
COOL FAN
ECONOMY
FAN SPEED
Wireless
Remote Control
Lift up about 90°.
|
|
|
> |
|