PANASONIC CQC9901U
Manual de Usuario

General
This chapter explains how to turn on or off the power, how to adjust the volume, etc.

Face Plate Removing/Mounting Power On/off

Power on
Press [SRC] (PWR: Power).
Notes: ¡ The opening screen appears. You can overwrite the opening screen (moving picture) with new one. (a page 40) ¡ When the power is switched on for the first time, a demonstration message appears on the display. Press [DISP] to change to regular mode. (a page 12)
SRC CS

Open/Eject
Press [ ] (OPEN).
SRC CS

When a disc is already loaded, the disc will automatically be ejected.

Tilt
Cautions: ¡ To avoid damaging the face plate, do not push it down or place objects on it while it is open. ¡ Do not pinch your finger or hand in the face plate. ¡ Do not insert foreign objects into the disc slots. ¡ For the following cases, the face plate automatically closes. Use caution not to catch your finger. ¡ After a lapse of 20 seconds ¡ When a disc is inserted ¡ When the face plate is removed (a page 14) The display angle changes among 4 levels as follows every time you hold down [ ] (TILT) for 1 sec. or more and release.

Power off
Hold down [SRC] (PWR: Power) for 2 sec. or more.
Note: The ending screen appears. You can overwrite the ending screen (moving picture) with new one. (a page 40) You can remove the face plate to prevent it from being stolen.

3 Put the face plate in the case.
Close
Press [ ] (OPEN).

Note: The last selected angle is maintained even after turning off the power.
TILT 1 TILT 2 TILT 3 OPEN

TILT OFF

Mounting Removing

1 Slide the left side of the face plate in
place.

q Up w Down Setting Range: 0 to 40 Default: 18

1 Turn off the power. (a page 14) 2 Press [ ] (Release).
(The face plate disengages with a click when it is removed.) (Anti-Theft System) (PWR: Power) The face plate automatically closes in 5 seconds if it is open or tilted. is active.

Notes: ¡ The volume level can be set independently for each source. (For radio, one volume setting for AM, one volume setting for all FMs) ¡ The volume is not adjustable while an error display is on the monitor. (a page 46)

2 Press the right end of the face plate
until �click� is heard.

The power is automatically turned off while the unit

Volume off (down)
Press [
(VOLUME) (OPEN/CLOSE, TILT)

](MUTE).
SRC CS

Cautions: ¡ It is recommended to remove or mount the face plate when the plate is at the closed position. Do not remove or mount the face plate when the plate is in motion. ¡ This face plate is not waterproof. Do not expose it to water or excessive moisture. ¡ Do not remove the face plate while driving your car. ¡ Do not place the face plate on the dashboard or nearby areas where the temperature rises to high levels.

Temporary Off (Down) Volume Adjustment Face Plate Motion (Open/Close, Tilt)

¡ Do not touch the contacts on the face plate or on the main unit, since this may result in poor electrical contacts. ¡ If dirt or other foreign substances get on the contacts, wipe them off with clean and dry cloth. ¡ To avoid damaging the face plate, do not push it down or place objects on it while it is open.

Cancel
Press [
MUTE (ATT: Attenuation)

](MUTE) again.

Note: Volume-down range can be specified. (a page 38)

14

CQ-C9901U/C9801U/C9701U

CQ-C9901U/C9801U/C9701U

General English
15