SHARP CPC440W
Manual de Servicio

SETTING THE CLOCK PREPARATION FOR USE
In this example, clock is set for the Replace the batteries if control distance decreases or oper24-hour (0:00) system.

1 Press ON/STAND-BY switch to enter the stand-by mode. Notes concerning use: 2 3
Periodically clean transmitter LED on the remote control and sensor on the main unit with a soft cloth. ON/

Press the CLOCK button.

ation becomes erratic.

Within 5 seconds, press the MEMORY/SET button.

STAND-BY Exposing sensor on the main unit to strong light may Press TUNING/TIME ( or ) button to select the time
(8" 20') Keep the remote control away from moisture, excessive heat,

4
MEMORY/
(AM 0:00 PM 11:59) (AM 12:00 PM 11:59) ( ) (0:00 23:59)

CLOCK of the unit. 0.2 6 m

display mode. interfere with operation. Change lighting or the direction

"0:00" � The 24-hour display will appear.

shock, and vibrations.

"AM 0:00" � The 12-hour display will appear. SET

CD-C440W/CP-C440W

"AM 12:00" � The 12-hour display will appear. 1 1 5

TUNING/TIME

Note that this can only be set when the unit is first installed or it has been reset (see below).

5 Press the MEMORY/SET button. 2 6 Press TUNING/TIME ( or ) button to adjust the hour.

3

4 matically to "PM".
RESETTING THE MICROCOMPUTER 8

Press TUNING/TIME button once to advance the time by 1 hour. Press for more than 0.5 seconds to advance continuously. When the 12-hour display is selected, "AM" will change auto-

0:00 AM 12:00

7 Press the MEMORY/SET button.

Press TUNING/TIME ( o r ) button to adjust the

5 Reset microcomputer under the following conditions: Press button for at least 0.5 seconds to change the time

minutes.

in 5-minute intervals. To erase all of the stored memory contents (clock and timer The hour setting will not even if minutes advance settings, tuner and CD presets). from "59" to "00". If the display is not correct.

OPERATION MANUAL

�6�

9 Press the MEMORY/SET button. If the operation is not correct. 1

6

2

The clock starts operating from "0" seconds. (Seconds are Note: contents of preset memory" on page 16.

not displayed.) To tuner preset memory, see "To erase all of the

7

2

8 is disconnected, the clock display will go out.

Note: In event of a failure or when the AC power lead Press ON/STAND-BY switch to enter the stand-by mode.

1 2 When AC power supply is restored, the clock display will Press VOLUME button, the TUNING/TIME button

flash on and off to indicate time when the power failure and ON/STAND-BY switch all at the same time. Hold occurred or when the AC power lead was disconnected. them down for at least 1 second.

If this happens, follow procedure below to change the

9

clock time.

time display mode: To change the clock time:

Press ON/STAND-BY switch to enter the stand-

1

by mode.

When the ON/STAND-BY switch is set to STAND-BY. When unit is in demonstration mode, press the DEMO button to enter the clock mode. x Press the MEMORY/SET button. Press VOLUME button, the TUNING/TIME

2

button and ON/STAND-BY switch all at the same y Perform steps 6 9 above. time. Hold them down for at least 1 second.

3 Perform steps 1 9 above. x Press the CLOCK button.

When the ON/STAND-BY switch is set to ON.

y Within 5 seconds, press the MEMORY/SET button.

Note: z Perform steps 6 9 above. The operation explained above will erase all data stored in memory, such as clock and timer settings, To see time display: (When the power is ON) tuner and CD presets.

Press the CLOCK button. The time display will appear for about 5 seconds.