CROSSLEE CL447CV-031244715901
Manual de Usuario

IMPORTANT USER INFORMATION
These notes are provided in the interest of safety. You must read them before installing or using the appliance.
� � This tumble dryer is intended for NORMAL DOMESTIC USE ONLY. Please note it is not recommended that the dryer be placed directly next to ovens or cookers, as the performance of the dryer may be affected. Adequate ventilation must be provided to avoid back flow of gases into the room from appliances burning other fuels, including open fires. Do not stack the tumble dryer on top of other appliances without the correct stacking kit. Any electrical work required to install the appliance should be carried out by a qualified person. It is important to clean the lint filter after each drying cycle or the restrictions to airflow will extend drying times and could cause the safety cut-out to trip. Exhaust air must not be discharged into a flue which is used for exhausting fumes from appliances burning gas or other fuels. Under no circumstances should anything other than the recommended articles be placed in the tumble dryer. The tumble dryer should be serviced by an appointed service organisation and only genuine parts used. It is dangerous to alter or modify the product in any way other than fitting authorised accessories. We recommend that the appliance is unplugged each time after use. It should always be disconnected from the electricity supply if it is to be left unattended for long periods (i.e. weekends, holidays etc.) The rear of the dryer gets quite hot during use, position the dryer so that the back is not accessible while in operation, but the sides have a space available to allow airflow. It is important to clean fluff from the window of the dryer and around the door seal after each drying cycle. Failure to do so could result in water leaking. � � � � � � DO NOT use a two-way adaptor, or extension lead. The dryer must be connected to its own socket. DO NOT block the air inlets at the front and back of your dryer. DO NOT allow fluff to accumulate around the tumble dryer. DO NOT exceed the recommended maximum load. DO NOT allow children to tamper with the controls and keep them away from the dryer when it is in operation. DO NOT place articles in the dryer if anything other than a water solution has been used in the cleaning process. DO NOT attempt to dry dripping wet articles or items containing foam rubber or rubber-like materials. DO NOT use the tumble dryer if you suspect that it is damaged in any way. Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause serious injury. Consult your local appointed service engineer and insist on genuine spare parts. The special mains cable and plug assembly must only be replaced with a genuine part available from the manufacturer or his service agent.

�

� � �

� �

� � � � �

�

This label, positioned on the rear of your dryer, indicates the surface is hot when operation avoid touching
CAUTION-HOT SURFACE

�

THIS APPLIANCE MUST BE EARTHED

LARGE BASIC

Reverse door and fit to dryer in closed position. Refit screws (G) and hinge cover (F). Open the door.

Open the door. Undo screw (A) remove switch strike (B) and replace screw. Remove screws (C) and latch plate (D). Remove hinge cover screw (E). Close the door.

Your dryer is supplied with a reversible door. To change the direction of opening proceed as follows for your type of door.

Dryers fitted with hinge cover:-

REVERSING THE DOOR OPENING

Large Door Opening:-

First remove the child safety peg from the top of the door by rotating 90° anticlockwise. Now unscrew the door hinges from the machine by removing the 4 screws. Do not use a power screwdriver as this may damage the threads. Remove the four screws from the opposite side of the door opening. Place these screws in the other side of the door opening. Reverse the door and re apply the hinge screws. Replace the child safe peg in the top of the, now reversed, door. Fit screw (E) to secure hinge cover. Remove screw (H) at top of door and refit switch strike (B) as shown. Pull the hinge cover (F) forwards to remove it. Remove two outer screws (G). Remove door. Fit latch plate (D) with screws (C). Open the door. Undo screw (A) remove switch strike (B) and replace screw. Remove screws (C) and latch plate (D). Remove hinge block screws (E). Remove door from hinge blocks. Refit latch plate (D) with screws (C). Remove screw (H) at top of door and refit switch strike (B) as shown. Fit door to hinge blocks and secure with screws (E).

B & L �03

Dryers fitted without hinge cover:-

Remove hinge screws (F) and hinge (G) and refit to opposite side as shown.

4213 094 5932A

IMPORTANT: PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE USING THIS APPLIANCE. KEEP THEM IN A SAFE PLACE FOR FUTURE REFERENCE.

INSTRUCTIONS FOR USE