WHIRLPOOL CDNS22V9
Manual de Usuario

Automatic

Ice

Maker

FOR YOUR SAFETY

MODELS WITH AUTOMATIC ICE MAKER The water inlet tubing assembly required to complete the water connection to the water valve is located in the crisper drawer in a bag. Connect the ice maker to the water supply as instructed in the separate instructions furnished with the refrigerator. The automatic icemaker is designed to furnish a continual supply of ice cubes, With this useful feature, you no longer have the inconvenience of filling ice cube trays, or the frustration of running out of ice. The amount of ice produced depends on the temperature in the freezer section We suggest you start with your refrigerator and freezer controls at their mid settings. In most cases, this is satisfactory. If the door to the refrigerator or freezer is your of opened refrigerator. frequently The colder the freezer kitchen arethe more ice high, a colder or temperatures in the section, abnormally is produced. setting may be necessary. After your model has been installed and the water supply contain connected undersized to the and ir_ _

Ice

Do not place fingers or hands on t the refrigerator is plugged in. Thi_ It will also prevent interference w and the heating element that rele Ice Pan Under certain rare circumstances, ic,

with a green-bhiish hue. The caus_ a combination of factors such as c_ hold plumbing and the accumulati _4"_% u

_ _ _ _%-,,,/-'71

b,

ply line which feeds the icemakeJ If such discoloration is observed, C from whom the refrigerator was !c Continued consumption of such dis Ice Dispenser

cubes. The first one or two harvests will, probably regular cubes because of air in the supply line.

The initial harvest may also contain impurities from the new water supply piping. Therefore, all cubes from the first two or three harvests should be discarded. Once this initial starting period is past, your icemaker will perform steadily icemaker, it may be_ to 12 hours before the icemaker furnishes any usable ice and dependably. Ice cubes that have been in the ice storage bin for a considerable length of time may pick up off-flavor taste, stick together, and gradually become smaller. We suggest that these cubes be thrown away. We also suggest using an open box of baking soda in the refrigerator for food odor absorption. may have a slight hum--the cubes will rattle as they fall into an empty storage pan--the water valve may click or "buzz" occasionally. All of these sounds are normal and should be ignored. The icemaker has a wire sensor arm that is connected to a shut-off switch. This arm stops the mechanism when the ice cube storage pan is full, and restarts it after several ice cubes have been used. You can use the stop arm to stop all productions Certain sounds ice at accompany All you need to do is of the the arm into the motor of may any time. the various cycles raise icernaker. The OFF position. The icemaker 1. Ice storage 2. Refrigerator should be turned off (arm up) when: for extended period of time. Also,

low the ice chute. Press the glass the fountain. To stop dispensing i penser motor and leave the glass i falling. With practice, you will lea prevent an unwanted dispense of _

I

|

Prevent ice cubes from missing yo_ To remove the ice dispenser bin, li Wash the bin occasionally in mild : push it all the way back until the at the front of the shelf it rests up( that turn the spiral auger are pos

_

Note: after installation, it may tak_ with cubes. NEVER ADD ICE CUB PENSER STORAGE BIN. THIS CC If this happens, remove the storag clumps that are stuck in the chu| those blocking the dispenser op_ motor.

bin is to be removed

To dispense water, press a contain of the fountain. To stop the watel ing, hold the container as high a

is not to be used for a considerable

time, such as vacations.

3. Water supply

is to be shut-off

for several

hours,

HOW THE ICEMAKER WORKS Water fills the empty cube mold when the freezer compartment has cooled to freezing temperature. Cold air is forced directly over mold. When frozen, the cubes are rotatedwater and out to the icemakerThe insweeperinstance, ejectspractical. into turn off the up supply of the mold. this arm if them the ice storage bin below. The sensor arm senses when the bin is full and signals the icemaker to stop ejecting more cubes. Meanwhile, the mold has been refilled and cubes frozen so the new supply is ready when needed. As soon as ice is removed from the bin, the sensor arm signals that more is needed. The icemaker resumes operation by ejecting ready-and-waiting frozen cubes.

refrigerator, air will escape from t] begins to flow. Draw 10 glasses oJ This will insure complete filling, Do not discard water into the grill, Whenyou area, not a drain. operate your disi first Normal spills w the spill shelf grille. Excessive sponge or cloth. The spill area s] sl

I1 _