Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5945 visitantes online.
Productos
Información
Destacado
Inicio >> CRATE >> CA30D Manual del propietario
 
 0 artículo(s) en Su carrito 

CRATE CA30D
Manual del propietario


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del CRATE CA30D Manual del propietario

Es una guía completa (también conocida como Manual de Operación o Manual del Propietario), y está disponible en formato PDF. Después de colocar su orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages: English

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
CA30D Acoustic Amplifier
The Front Panel:

1

2

3

4

5

6

7

8

9

10

11

12

13

1: Power. Use this switch to apply power to the amplifier: the amp is on when the top of the switch is depressed, off when the bottom of the switch is depressed. The switch illuminates when the amp is on. 2: Line Out. Use this jack to connect a high impedance, unbalanced line level signal to a house sound board, a recording console or another amplifier. 3: Insert. Use this jack to add external effects to the signal. The ring = send (line out), tip = return (line in), sleeve = ground. This jack can also be used to �chain� multiple amplifiers together, since connecting to this jack does not interrupt the signal going to the amplifier. (See the illustrations on page 5 for more information.) 4: Effects Level. Use this control to adjust the amount of digital signal processing applied to the output signal. 5: Effects Mode. Use this control to select the type of digital signal processing applied to the output signal. (See the section entitled �The DSP Section� on page 6 for more information.) 6: High. This serves as the treble control for both channels. Adjust this control so your high notes and harmonic overtones are lively but not overpowering. 7: Contour. Use this control to set the center point of the mid control. This control should be set at the frequency which gives you the most natural midrange tones.

8: Mid. This serves as the midrange control for both channels. Adjust this control to get the best projection and midrange tones for your instrument. The center point of the mid control is chosen by the setting of the contour control (#7). 9: Low. This serves as the bass control for both channels. Adjust this control to get the best sounding bass response for your instrument. Excessive boost of the low control can cause an unnatural howling (acoustic feedback from your instrument) and should be avoided. 11,13:Input 2, Input 1. The signal output from your acoustic instrument, tape player, rhythm machine, high-Z microphone or other source may be connected to either or both of these jacks by means of a shielded signal cable. Each of the input jacks is governed by its corresponding gain control (#10 for Input 2, #12 for Input 1). The signals from these two jacks are summed together after their gain stages. 10,12:Gain 2, Gain 1. Use these controls to set the input gain level for the corresponding input jack. These controls set the level of the input signal and serve as the amplifier�s volume controls. 14: AC Line Cord. (Rear panel, not shown) The grounded power cord should only be plugged into a grounded power outlet that meets all applicable electrical codes and is compatible with the voltage, power, and frequency requirements stated on the rear panel. Do not attempt to defeat the safety ground connection.

4

Quizás también quiera comprar

$4.99

CA30D CRATE
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …
>
Parse Time: 0.144 - Number of Queries: 103 - Query Time: 0.037