CASIO BGX260-2A
Manual de Usuario

Operation Guide 2960
To configure Home Site data 1. In the Timekeeping Mode, hold down A until the seconds start to flash, which indicates the setting lllllllll screen. 2. Press A again to display the GMT differential setting screen. 3. Press C to move the flashing in the sequence shown below to select other settings. To set the current time in the World Time Mode 1. In the World Time Mode, use D to select the city code whose time you want to set. 2. After you select a city code, hold down A until the DST llll on/off setting of the world time starts to flash, which lll l ll indicates the setting screen. 3. Use C to move the flashing in the sequence shown below to select other settings.
DST indicator

l l

GMT differential

L

GMT differential

Longitude

Lunitidal Interval Hours

Lunitidal Interval Minutes

4. When the setting you want to change is flashing, use D and B to change it as described below. Setting GMT differential Screen Button Operations Use D (+) and B (�) to change the setting. � You can specify a value in the range of �11.0 to +14.0, in 0.5-hour unit. Use D (+) and B (�) to change the setting. � You can specify a value in the range of 179°W to 180°E, in 1-degree units. Use D (+) and B (�) to change the setting.

4. When the setting you want to change is flashing, use B and D to change it as described below. To change this setting DST on/off Hour, Minutes Perform this button operation Press D to toggle between Daylight Saving Time (ON) and standard time (OF). Use D (+) and B (�) to change the setting.

Longitude

Lunitidal Interval Hours, Minutes 5. Press A to exit the setting screen.

� When setting the world time using the 12-hour format, take care to set the time correctly as a.m. (no indicator) or p.m. (P indicator). 5. Press A to exit the setting screen. � Note that you cannot switch between Standard Time and Daylight Saving Time while GMT is selected as the city code. � Note that the DST/Standard Time setting affects only the currently displayed city code. Other city codes are not affected. � The DST indicator is on the display whenever you display a city code for which Daylight Saving Time is turned on.

Moon/Tide Data
Moon phase indicator

Countdown Timer
Moon/tide data lets you view the Moon age and Moon phase for a particular date, and tidal movements for a particular date and time for the Home Site. � If you suspect that the Moon/tide data is not correct for some reason, check the Timekeeping Mode data (current time, date, and Home Site settings), and make changes as required. � See �Moon Phase Indicator� for information about the Moon phase indicator and �Tide Graph� for information about the tide graph. � All of the operations in this section are performed in the Moon/Tide Data Mode, which you enter by pressing C. The countdown timer can be set within a range of one minute to 60 minutes. An alarm sounds when the

l

Minutes

Moon age

Configuring the Countdown Timer
The following are the settings you should configure before actually using the countdown timer. Countdown start time and reset time Timer mode (auto-repeat, elapsed time)

Moon/Tide Data Screens
Each press of A in the Moon/Tide Data Mode toggles between the Moon Data screen and the Tide Data screen.
Moon phase indicator

Moon Data Screen

Tide Data Screen
Tide graph

Progress beeper on/off � See �To configure the countdown timer� for information about setting up the timer.
Reset Time You can specify any point between the countdown start time and the end of the countdown as the �reset time�. Then while a countdown operation is in progress, you can press a button to jump to the reset time and resume the countdown from there. Timer Mode The countdown timer gives you a choice of two modes: auto-repeat and elapsed time. Auto-repeat The auto-repeat mode automatically restarts the countdown from the countdown start time you set whenever zero is reached. � The auto-repeat mode is best when timing the starts of match races. � Even if you start a countdown operation from the reset time, the countdown automatically restarts from the countdown start time whenever it reaches zero. � Auto repeat timing repeats up to seven times. Elapsed Time When the end of the countdown is reached in the elapsed time mode, the timer automatically switches to an elapsed time measurement operation. � The elapsed time mode is best when timing the speed of yachts during ocean races. � The elapsed time operation is performed in one-second increments up to 99 hours, 59 minutes, 59 seconds.

Press A.
Month � Day Time

Moon age Year

� When you enter the Moon/Tide Data Mode, the data that appears first is the Moon data (Moon age and Moon phase indicator) for the current date as kept by the Timekeeping Mode.

To view the Moon data for a particular date While the Moon Data screen is displayed in the Moon/Tide Data Mode, use D (+) to display the date whose Moon data you want to view. � You can select any date starting from the date currently indicated in the Timekeeping Mode, up to the year 2039. Display of past Moon data and tide data is not supported. To view tide data for a particular time 1. While the Moon Data screen is displayed in the Moon/Tide Data Mode, use D (+) to display the date whose tide data you want to view. 2. Press A to switch to the Tide Data screen. � The initial screen shows the tide graph for 6:00 AM. 3. Specify the time for which you want to display tide data. � Use D (+) to change the time in one-hour steps.

Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed about the countdown status without looking at the display. The following describes the types of beeper operations the watch performs during a countdown. Countdown End Beeper The watch emits a short beep each second of the final 10 seconds at the end of a countdown, and a long beep when the countdown reaches zero. � The countdown end beeper always sounds, regardless of the on/off status of the progress beeper. Progress Beeper The progress beeper actually includes two beepers: a reset time beeper and a reset period progress beeper. � The reset time beeper and reset period progress beeper sound only while the progress beeper is turned on. Reset Time Beeper The reset time beeper is similar to the countdown end beeper. When the progress beeper is turned on, the watch beeps each second of the final 10 seconds before the countdown reaches the reset time. Reset Period Progress Beeper The reset period is the portion of the countdown between the reset time and zero. When the progress beeper is turned on, the watch emits four short beeps at the top of each minute during the reset period, and 30 seconds before the end of the countdown.

World Time
Current time in the selected city code

WT

The World Time shows the current time in 27 cities (29 time zones) around the world. � The time settings of the Timekeeping Mode and the World Time Mode are independent from each other, so you must make separate settings for each. � Whenever you change the time setting for any city in the World Time Mode, the settings of all other cities are changed accordingly. � For full information on city codes, see the �City Code Table�. � All of the operations in this section are performed in the World Time Mode, which you enter by pressing C.

City code GMT differential

To view the time in another city code In the World Time Mode, press D to scroll through city codes (time zones).

lllllllll

l

llllllll

l

ll

DST on/off

Hour

Minutes

L

Seconds

countdown reaches zero. The countdown timer has two modes: auto-repeat and elapsed time, and a progress beeper signals the progress of the countdown. All of this makes the countdown timer a valuable tool for timing the start of a surfing or a yacht race. � All of the operations in this section are performed in the Countdown Timer Mode, which you enter by pressing C.

ll

2