PHILIPS AZ1325/17B
Manual de Usuario

CD PLAYER
Programming track numbers
In the stop position, select and store your CD tracks in the desired sequence. Up to 20 tracks can be stored in the memory. 1. Press SEARCH � or § on the set to select your desired track number. 2. Press PROG. � Display: PROG, Prog briefly and your selected track number. (See 5) � If you attempt to program without first selecting a track number, noSE is shown. 3. Repeat steps 1-2 to select and store all desired tracks. � Display: FULL if you try to program more than 20 tracks.

SAFETY AND MAINTENANCE
SAFETY & MAINTENANCE INFORMATION (See 7)
� Don't expose the set, batteries, CDs to humidity, rain, sand or excessive heat. � Clean the set with a dry cloth. Don't use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the set. � Place the set on a hard and flat surface so that the system does not tilt. Make sure there is good ventilation to prevent the set overheating. � Apparatus shall not be exposed to dripping or splashing. � Do not place any sources of danger on the apparatus (e.g. liquid filled objects, lighted candles). � The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated.

TROUBLESHOOTING
If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service center.

WARNING: Do not open the set as there is a risk of electric shock. Under no circumstances should you try to repair the set yourself, as this will invalidate the warranty.
No sound /power � � � � � � � � Volume not adjusted Adjust the VOLUME Power cord not securely connected Connect the AC power cord properly Batteries drained/ incorrectly inserted Insert (fresh) batteries correctly Headphones connected to the set Disconnect headphones dAtA indication � CD contains non-audio files � Press SEARCH � or § once or more to skip to a CD audio track, instead of the data file The CD skips tracks � CD damaged or dirty � Replace or clean CD � SHUFFLE or PROG is active � Switch off SHUFFLE / PROG Remote control does not function properly (For AZ1325 only) � Batteries exhausted/ incorrectly inserted � Insert (fresh) batteries correctly � Distance/ angle between the set too large � Reduce the distance/ angle

Severe radio hum or noise � Electrical interference: set too close to TV, VCR or computer � Move the set to increase the distance Poor radio reception � Weak radio signal � FM: Adjust the FM telescopic antenna nocd indication � � � � CD badly scratched or dirty Replace/ clean CD, see Maintenance Laser lens steamed up Wait until lens has cleared

Reviewing the program
In the stop position, press and hold PROG until the display shows all your stored track numbers in sequence.

CD player and CD handling
� If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. � The lens of the CD player should never be touched! � Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. � Always close the CD door to avoid dust on the lens. � To clean the CD, wipe in a straight line from the center towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc. � Never write on a CD or attach any stickers to it.

Erasing a program
You can erase the program by either: � pressing 9 twice � CLr is displayed briefly and PROG disappears. � You select AM / FM function. � Open the CD door.

nFcd indication � CD-R(W) is blank/ not finalized � Use a finalized CD-R(W)

Environmental information
We have done our best to reduce the packaging and make it easy to separate into 3 materials: cardboard, expandable polystyrene, polyethylene. Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging, dead batteries and old equipment.