|
Usuarios conectados
Actualmente hay 6043 visitantes online.
|
Productos
|
Información
|
Destacado
|
|
|
|
|
No hay comentarios de productos.
General Operation
General operation
1 Using AC Mains Check if the mains voltage, as shown on the type plate located on the back of the set, corresponds to your local mains supply. If it does not, consult your dealer or service center. If your set is equipped with a voltage selector, adjust the selector so that it matches with the local power supply. Connect the mains lead to the AC ~ inlet and the wall socket.The mains lead is now connected and ready for use. To switch the set off completely, withdraw the mains lead from the wall socket. Disconnect the mains lead from the wall socket to protect your set during heavy thunderstorms. Helpful hints : To avoid unnecessary energy consumption, always adjust the Source selector to TAPE/OFF after using the set. Also check that the tape deck keys are released The type plate is located on the back of the set. 1 Switching on and off and selecting functions To switch on, push the Source selector slider to CD, TUNER, or TAPE/OFF as desired. � In CD or TUNER, the display lights up blue. � In TAPE, the display lights up during tape operation 2 To switch off, push the Source selector slider to TAPE/OFF and check the cassette keys are released. Helpful hints: � To change from TAPE to TUNER or CD function, or when you are switching off the set: first, make sure you press the tape STOP�EJECT 9/ key to end playback and all the cassette keys are released. � The radio presets will be retained in the set�s memory. Adjusting volume and sound Adjust the volume with the VOLUME control. Press DBB once or more to select dynamic bass boost on or off.
Digital Tuner
Digital tuner
1 Tuning to radio stations Push the Source selector slider to TUNER. � The display lights up blue and if programmed, a preset number appears (see 3). � Then, the display shows radio station frequency and waveband. If programmed, MEMORY appears. (see 4) 2 Press STOP/BAND 9 to select your desired waveband, FM or MW. � For FM, adjust MONO�STEREO to STEREO. Press and hold � or § until the frequency in the display starts running. � The radio automatically tunes to a station of sufficient reception.The frequency keeps running during automatic tuning. � STEREO lights up for stereo FM reception. Repeat step 3 if necessary until you find the desired station. � To tune to a weak station, press � or § briefly and repeatedly until you have found optimal reception. To improve radio reception: � For FM, extend, incline and turn the telescopic aerial. Reduce its length if the signal is too strong. � To tune to a weak FM station, adjust MONO�STEREO to MONO. � For MW, the set uses a built-in aerial. Direct this aerial by turning the whole set. 2 Programming radio stations You can store up to a total of 20 radio stations in the memory (10 FM and 10 MW), manually or automatically (Autostore). Manual programming 1 Tune to your desired station (see Tuning to radio stations). 2 Press PROG to activate programming. � Display: P01. MEMORY flash. Press ALBUM/PRESET -/+ once or more to allocate a number from 1 to 10. Press PROG to confirm. Repeat steps 1-4 to store other stations.
2
3
3 4 5
4 �
3
Helpful hints: You can erase a preset station by storing another frequency in its place. Autostore Autostore automatically starts programming radio stations from preset 1. Any previous presets e.g. manually programmed will be erased. 1 In TUNER mode, press STOP/BAND 9 to select FM or MW. Press and hold PROG until the frequency and MEMORY flash. � Available stations are programmed (FM or MW. P and a preset number (1 - 10) appears when a station is stored. � After all stations are stored, the first autostore preset station automatically plays. To listen to a preset station Press the ALBUM/PRESET -/+ button once or more until the desired preset station is displayed.
4
1 2
|
|
|
> |
|