No hay comentarios de productos.
CD Player
Playing a CD
This CD player plays Audio Discs including CD-Recordables (CD-R) and CDRewritables (CD-RW). � 1 2 MP3, CD-ROM, CD-I, CDV,VCD, DVD or computer CDs are not possible for playback. Adjust the Source selector to CD. Open the CD door, and insert a CD with the printed side facing up, then press the CD door gently to close. � Display shows --, and later the total number of tracks. (See 3) 3 4 5 6 Press 2 PLAY / ; PAUSE to start playback. To pause playback, press 2/;. � Display: PLAY flashes. (See 4) To resume, press 2/; again To stop CD playback, press 9. 5 4 2 3 1
CD Player Programming track numbers
You may store up to 20 tracks in the desired sequence. If you like, store any track more than once. In the stop position, press PROG to activate programming. � Display: PROG and 00 flash. (See 5) Press � or § to select your desired track number. Press PROG to store the desired track number. � Display: PROG and 00 flash for you to program the next track.. Repeat steps 2 to 3 to select and store all desired tracks in this way. � If you attempt to store more than 20 tracks, no track can be selected and the display shows --. To play your program, press 2/;. 1 2
Cassette Recorder
General information on recording � Recording is permissible insofar as copyright or. other rights of third parties are not infringed. � For recording, use only NORMAL type cassettes (IEC type I) on which the tabs have not yet been broken.This deck is not suited for recording on CHROME (IEC II) or METAL (IEC IV) type cassettes. � The best recording level is set automatically. Altering the VOLUME or BASS BOOST will not affect the recording. To protect a tape from accidental erasure, break out the tabs. If you wish to record again, cover the tabs with a piece of adhesive tape. Recording from the CD Player Select CD source. Insert a CD, or if desired, program track numbers. Press STOP�EJECT to open the cassette holder. Insert a blank tape and close the deck. 4 5 6 7 Press REC to start recording. Press 2/; PLAY/PAUSE to start CD playback. For brief interruptions press PAUSE. To resume recording, press PAUSE again. To stop recording, press STOP�EJECT. Recording from the Radio 1 Select TUNER source. Tune to the desired radio station (see Radio reception). Follows steps 3, 4, 6,7 under Recording from the CD Player. 2 3
Different play modes: REP. and REP. A (See 6, 7)
You can select and change the play modes before or during playback, and combine the modes with PROG. REP. � plays the current track continuously. REP. A � repeats the entire CD/program 1 To select play mode, press REPEAT once or more. � The display shows REP. or REP. A. 2 Press 2; to start playback if in the stop position. 3 To return to normal playback, press REPEAT repeatedly until the modes are no longer displayed. � You can also press 9 to cancel your play mode.
�
1 2 3
Cassette playback
Adjust the Source selector to TAPE/ OFF. Press STOP�EJECT to open the cassette holder and insert a cassette, and close the deck. Press PLAY to start playback. To pause playback, press PAUSE. To resume, press the key again. By pressing F.FWD/ REW, fast winding of the tape is possible in both directions. To stop fast winding, press STOP�EJECT. To stop the tape, press STOP�EJECT.
Helpful hints : CD play will also stop when:
� you open the CD door; � you select TUNER or TAPE/ OFF sound
source;
Helpful hints :
� the CD has reached the end.
� When playback of your program comes to
the stop position, your set will return to normal playback.To re-enter program mode, press PROG in the stop position. 3 4 5 6
Selecting a different track
� Press �/ § once or repeatedly until the desired track number appears in the display. � In the pause/stop position, press 2/; to start playback.
Reviewing the program
In the stop position, press PROG repeatedly to see your stored tracks.
Finding a passage within a track
1 During playback, press and hold � or § . � The CD is played at high speed and with reduced volume. 2 When you recognize the passage you want, release � or § to resume normal playback. Helpful hints : When searching within a final track and you reach the end of the last track, the CD goes to stop mode.
Erasing a program
You can erase the contents of the memory by: � selecting TUNER or TAPE/ OFF sound source; � opening the CD door; � in the stop position, press PROG to enter program mode, and then press 9. Helpful hints: � During playback, the keys are automatically released at the end of a tape and the set is switched off (unless PAUSE mode has been activated.) � During fast forwarding/rewinding, the keys will not be released at the end of a tape. To switch off the set, make sure the cassette keys are also released.
