PHILIPS AZ1017/55
Manual de Usuario

Safety & Maintenance
Safety information
� �

(See 7) Tape deck maintenance
To ensure quality recording and playback of the tape deck, clean parts A, B and C as shown, once a month. Use a cotton bud slightly moistened with alcohol or a special head cleaning fluid to clean the deck. 1 2 3 4 Open the cassette holder by pressing 9/. Press 1 and clean the roller C. Press ; and clean the heads A, and the capstan B. After cleaning, press 9. � Cleaning of the heads can also be done by playing a cleaning cassette through once.

Troubleshooting
If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre.

Place the set on a hard, flat and stable surface so that the system does not tilt. Do not expose the set, batteries, CDs to humidity, rain, sand or excessive heat caused by heating equipment or direct sunlight. Do not expose the apparatus to dripping or splashing. Adequate ventilation with a minimum gap of 6 inches between the ventilation holes and surrounding surfaces is necessary to prevent heat build-up.

WARNING: Do not open the set as there is a risk of electric shock. Under no circumstances should you try to repair the set yourself, as this will invalidate the guarantee. Problem � Possible cause � Remedy No sound /power � � � � � � � Volume not adjusted Adjust the VOLUME Power cord not securely connected Connect the AC power cord properly Batteries dead/ incorrectly inserted Insert (fresh) batteries correctly CD contains non-audio files Note: Make sure the CD is not encoded with Copyright protection technologies, as some do not conform to the Compact Disc standard. - - indication � � � � � No CD inserted Insert a CD CD badly scratched or dirty Replace/ clean CD, see Maintenance Laser lens steamed up

� �

�

The ventilation should be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.. No objects filled with liquids, such as vases, shall be placed on the apparatus. No naked flame sources, such as lighted candles, should be placed on the apparatus. The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated. To clean the set, use a dry cloth. Do not use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the housing. � � � � �

� � �

CD player and CD handling
If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. The lens of the CD player should never be touched! Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. Always close the CD-tape door to avoid dust on the lens. To clean the CD, wipe in a straight line from the center towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc. Never write on a CD or attach any stickers to it.

� Press � , § once or more to skip to a CD audio track, instead of the data file.

� Wait until lens has cleared

Display does not function properly/ No reaction to operation of any of the controls � Electrostatic discharge � Switch off and unplug the set. Reconnect after a few seconds The CD skips tracks � CD damaged or dirty � Replace or clean CD � Program is active � Quit program mode

� CD-R(W) is blank or not finalized � Use a finalized CD-R(W) or suitable CD Audio disc only Poor cassette sound quality � Dust and dirt on the heads, etc. � Clean deck parts, see Maintenance � Use of incompatible cassette types (METAL or CHROME) � Only use NORMAL (IEC I) for recording Recording does not work � Cassette tab(s) may be broken � Apply adhesive tape over the missing tab space

�

Environmental information
All unnecessary packaging material has been omitted.The packaging can be easily separated into three materials: cardboard, polystyrene and plastic. Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging, dead batteries and old equipment.

�