Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5854 visitantes online.
Productos
Información
Destacado
Inicio >> PIONEER >> AVIC-D3/XU/UC Manual de Servicio
 
 0 artículo(s) en Su carrito 

PIONEER AVIC-D3/XU/UC
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del PIONEER AVIC-D3/XU/UC Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages: English

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
5

6

7

8

There are two methods for adjustment, a method whereby the adjustment is made while monitoring the RF waveform using the oscilloscope (method 1) and a method whereby the adjustment is made while checking the RF level in value by OSD (method 2). The adjustment procedure is shown below. Refer to the paragraph for the service test mode regarding entering of the test mode and the operation procedure. Adjustment procedure: 1. Turn the DVD mechanism module upside down so that the pick up can be adjusted. When the module is turned upside down, there is a possibility that the disc is rubbed. So, first place a coin with the thickness of approximately 1.5mm on a desk, and set the module upside down in a way that section 1 in the illustration below comes right above the coin.

A

B

2. Install the pick up. (Refer to the section regarding removal of the pick up from the mechanism unit.) As for the precautions in handling the pick up, refer to the precautions in handling the PU as described below. 3. Method 1: Connect the oscilloscope by referring to the connection drawing so that the RF signal can be monitored with AGND2 as the reference. Method 2: There is no need for setting of any equipment. Proceed to step 4. 4. Turn the power ON, and load the disc for adjustment.(GGV1018) 5. After setting the disc type to DVD layer 1 in the front end test mode, turn the power ON, and move the pick up to the inner periphery. (CRG - Home) 6. Turn the LD ON. 7. Set to focus close, and make auto adjustment for all items under that state, then set to tracking close. And make auto adjustment for all items under that state as well. 8. Make an intermediate periphery (ID: 100 000) search, and move the PU to intermediate periphery. 9. Method 1: Proceed to step 10. Method 2: After setting to Tracking Open, make all auto adjustments, and set to Tracking Close this time with a command that can be RF displayed. Make auto adjustment for all items under that state as well. 10. Use TORX driver (T2) (GGK1095) for the following. Method 1: While monitoring the RF waveform on the oscilloscope, turn SKEW adjustment screw A just a little bit in a way that the level will reach the maximum. While the pick up is at the intermediate periphery, turn SKEW adjustment screw B just a little bit in a way that the level will reach the maximum. While the pick up is at the intermediate periphery, turn SKEW adjustment screw A just a little bit in a way that the level will reach the maximum. (Make adjustment in the order of A -> B -> A, Please end the each adjustment by turning screw clockwise. ) Method 2: While monitoring the RF level value on the OSD display, turn the SKEW adjustment screw A just a little bit in a way that the level will reach the maximum. While the pick up is at the intermediate periphery, turn SKEW adjustment screw B just a little bit in a way that the level will reach the maximum. While the pick up is at the intermediate periphery, turn SKEW adjustment screw A just a little bit in a way that the level will reach the maximum. (Make adjustment in the order of A -> B -> A, Please end the each adjustment by turning screw clockwise. ) If the error rate is not good, please perform Method 1 again. 11. Turn the power OFF in the test mode, and after confirming that the disc has stopped, eject the disc. 12. Apply adhesive for fixing the SKEW and lock the screw. Refer to the illustration below for the adhesion points.
F C

D

E

AVIC-D3/XU/UC
5 6

7

8

171

Quizás también quiera comprar

$4.99

AVIC-D3/XU/UC PIONEER
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …
>
Parse Time: 0.23 - Number of Queries: 101 - Query Time: 0.056