PHILIPS AJ3011/00
Manual de Usuario

English
CONTROLS 1 Display - shows the clock / alarm (small display) times and status of the set 2 TIME SET - to set the clock time 3 HR, MIN - to adjust the hours (HR) and minutes (MIN) for clock /alarm times 4 ALARM SET - to set the alarm time 5 SLEEP / RADIO ON - to activate sleep mode and adjust the sleep time - to switch on the radio 6 ALARM RESET/ RADIO OFF - to stop the active alarm for 24 hours - to stop RADIO / SLEEP function 7 REPEAT ALARM / BRIGHTNESS CONTROL - to switch off the alarm for a 8 - 9 minute period - to change the brightness of the display illumination - to stop SLEEP function 8 ALARM - to select alarm mode OFF / RADIO / BUZZER 9 VOLUME - to adjust the sound level 0 BAND - to select FM-MW (or LW) waveband ! TUNING - to tune to radio stations @ Pigtail aerial - to improve FM reception # Mains cord - for AC mains supply $ RESET - press if the set does not react to operation of any button % Battery compartment - for backup batteries The type plate and the production number are located on the bottom of the set. INSTALLATION POWER SUPPLY AND DEMO MODE 1 Check if the mains voltage, shown on the type plate on the bottom of the set, corresponds to your local mains supply. If it does not, consult your dealer or service centre. 2 Connect the mains plug into the wall socket. The mains supply is now switched on and the display will show the PHILIPS demo mode. � PH..IL..IPS scrolls across the display continuously. � Press the TIME SET to exit the demo mode and enter time setting mode. Helpful Hint : If power breakdown backup batteries are inserted, the display will also show the PHILIPS demo mode. 3 To disconnect the set completely from the mains supply, withdraw the mains plug from the wall socket. POWER BREAKDOWN BACKUP When the mains power fail, the complete clock radio will be switched off. When the mains supply returns, the display will show the PHILIPS demo mode and the correct clock time has to be set again. To retain the clock time and the set alarm time in the event of an AC mains failure or disconnection, insert two 1.5V batteries, type R06, UM3 or AA size (not supplied) into the battery compartment: this will act as a power backup to retain the clock and alarm times only. (Operation of the backlight illumination, alarm and radio are excluded). 1 Open the battery door to insert batteries as indicated by the + and � symbols inside the battery compartment. Close the battery door. 2 Connect the mains plug to the wall socket. � Replace the batteries once a year, or as often as necessary. � Old and new or different types of batteries should not be used in combination. Batteries contain chemical substances, so they should be disposed of properly. BASIC FEATURES ILLUMINATION BRIGHTNESS Press REPEAT ALARM / BRIGHTNESS CONTROL once or more. � The brightness of the display will change in this sequence: BRIGHT � DIM � BRIGHT... Helpful Hint : When an alarm or the SLEEP function is active, brightness cannot be adjusted. SETTING THE CLOCK The time is displayed using the 24 hour clock. 1 Press TIME SET for more than 2 seconds to enter time setting mode. � Time displays and flash. 2 Press HR or MIN repeatedly or hold down on the button to adjust the hours and minutes respectively. Release HR or MIN when you reach the correct setting. 3 After you have set both the hours and minutes, press TIME SET to confirm the correct setting. � Clock time also starts to run automatically after 60 seconds after you adjust the time. Helpful Hint : Press ALARM SET during time setting will switch to alarm setting mode. RADIO

1 2 3 4 5

Press SLEEP / RADIO ON once to switch on the radio. Select your waveband using the BAND switch. Use TUNING to find your radio station. Adjust the sound using VOLUME. Press ALARM RESET / RADIO OFF to switch off.

To improve reception: FM: extend and position the pigtail aerial to obtain optimum reception. MW (or LW): uses a built-in antenna inside the set. Direct the antenna by adjusting the position of your set. SETTING THE ALARM General If you wish to use the alarm, first set the alarm time. There is a choice of two alarm modes, buzzer or radio. The alarm display shows the alarm time all the time and the alarm indicator appears if the alarm is set. Setting the alarm time and mode 1 Press ALARM SET for more than 2 seconds to enter alarm time setting mode. � ALARM and the alarm time digits flash. 2 Press HR or MIN repeatedly or hold down on the button to adjust the hours and minutes respectively. Release HR or MIN when you reach the correct setting.

3

Press ALARM SET to confirm alarm time setting.