JVC AA-P30U
Manual de Usuario

CHARGING THE BATTERY PACK
Power cord

SUPPLYING POWER

1 the AC Adapter/Charger. Connect one end
2
of the power cord to the AC Adapter/ Charger and the other end to the wall outlet. The POWER indicator lights.

Make sure you unplug the DC cable from

You can connect the camcorder to an AC outlet using the AA-P30 AC Adapter/Charger. Connect one end of to 1 AC Adapter/Charger the power cordend the and the other to the wall outlet.

1
AC Adapter/Charger AA-P30

2

Remove the battery pack�s protective cap. Attach the battery pack with the mark aligned with the corresponding marks on the AC Adapter/Charger. The CHARGE Indicator begins blinking to indicate charging has started. When two battery packs are attached, they will be recharged in the order that they are attached.

CHARGE indicator 1 POWER indicator CHARGE indicator 2

DC cable To AC outlet

2
To DC Input connector

2 camcorder. AC Adapter/Charger to the Connect the
MEMO: � Be sure to use the DC cable provided with the AC Adapter/Charger. � When using the DC cable, make sure to connect the end of the cable with the

1
Power cord AC Adapter/Charger

3

3

When the CHARGE indicator stops blinking but stays lit, charging is finished. Slide the battery and lift off. Remember to unplug the AC Adapter/Charger�s power cord from the AC outlet.

2
To DC Output connector

core filter to the AC Adapter/Charger. The core filter improves the performance of the equipment.

DURING USE . . .
MEMO: � Perform charging where the temperature is between 10°C (50°F) and 35°C (95°F). 20°C (68°F) to 25°C (77°F) is the ideal temperature range for charging. If the environment is too cold, charging may be incomplete. � When plugging the power cord into an AC Adapter/Charger, push it all the way in until it stops. � The AC Adapter/Charger AA-P30 is specifically designed to charge the BN-V416 or BNV428 Battery Packs. It cannot be used to charge a BN-V408. � When charging a brand new Battery Pack, or one that�s been in storage for an extended period, the Charging Indicator may not come on. In this case, remove the Battery Pack, then reattach and try charging again. � If you connect the DC cable to the DC Connector while a Battery Pack is being charged, power will be supplied to the camcorder and charging will end incomplete. � Vibration noise can sometimes be heard coming from the inside of the AC Adapter/Charger. This is normal. � The AC Adapter/Charger processes electricity internally, and will become warm during use. This is normal. Make sure to use the AC Power Adapter/Charger in well-ventilated areas only. � If the battery operation time remains extremely short even after having been fully charged, the battery is worn out and needs to be replaced. Please purchase a new one.

TIME TAKEN FOR RECHARGING
Battery pack BN-V416 BN-V428 Recharging time of a single pack Approx. 2 hr. 10 min. Approx. 3 hr. 20 min. Successive recharging time of two packs Approx. 4 hr. 20 min. Approx. 6 hr. 40 min.

SPECIFICATIONS
Power USA and Canada AC 120 V`, 60 Hz European countries AC 220 V to 240 V `, 50 Hz/60Hz Other countries AC 110 V to 240 V`, 50 Hz/60 Hz 23 W , 1.2 A (charge) , 2.3 A (VTR) Operating temperature Dimensions Mass Accessories 0°C to 40°C (32°F to 104°F) [when charging, 10°C to 35°C (50°F to 95°F)] 122 mm (W) x 51 mm (H) x 92 mm (D) Approx. 280 g (Main body only) Power cord : Approx. 2 m DC cable : Approx. 2 m Warranty Card (USA and Canada only)

* When charged at temperatures between 20°C (68°F) and 25°C (77°F). �When charging Battery Packs after a long storage period, charging time will be longer than the time indicated above.
Power consumption

Output power DC 7.2 V DC 6.3 V

6

7

English