Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5557 visitantes y 
16 usuarios online.
Productos
Información
Destacado
Inicio >> TOSHIBA >> 40PW03G Manual de Servicio
 
 0 artículo(s) en Su carrito 

TOSHIBA 40PW03G
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del TOSHIBA 40PW03G Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages: English

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON PAGE 3 OF THIS MANUAL.

PICTURE TUBE COMPONENTS ADJUSTMENT
ADJUSTING PROCEDURE IN REPLACING CRT Cutoff Lens focus Electrical focus RGB FOCUS ADJUSTMENT User convergence center check 1. Call-up the adjustment mode (see page 10) 2. Press a button on the remote controller in order to display Centering (PAL) the internally-generated cross-hatch (See TEST SIGNAL SELECTION on page 11.) Convergence adjustment 3. Expose only RED by covering the GREEN and BLUE (PAL/NTSC) lenses with caps. 4. Loosen the RED lens fixing screws (refer to Fig. a), and White balance adjust the RED lens focus to obtain the sharpest point while observing the middle and peripheral sections of the Sub bright adjustment screen. End DESCRIPTION OF NECK COMPONENTS 2 1 Fig. a 5. Use the focus VR of �R� of the focus pack in order to adjust the electric focus in the middle and peripheral sections of the screen to its sharpest level. 6. Check the RED focus of the whole screen and if necessary repeat steps 4 and 5. 7. Fix the RED lens by tightening its fixing screws. 8. Expose only GREEN by covering the RED and BLUE lenses with caps. 9. Display the internally-generated cross-hatch signal. 10. Adjust the GREEN lens focus on the left border of the screen to its sharpest level, then check the focus on the right border, and if it is at its sharpest level, fix it in that position by tightening the lens screws. (1) If the horizontal line toward the right border is redflared, turn the lens screw slightly right in order to balance it with the left border. (After adjustment, the left border tends to be slightly green-flared, and the right border tends to be slightly red-flared.) (2) If the horizontal line toward the right border is greenflared, turn the lens screw slightly left in order to balance it with the left border. (After adjustment, the left border tends to be slightly red-flared, and the right border tends to be slightly green-flared.) Note: The aim of the above-described adjustment procedure for the Green lens focus is to obtain the best lens focus after 2 - 3 hours of warming up taking into account the focus drift; it applies if the warming up time before the adjustment is less than 30 minutes. (The horizontal line in the screen middle section tends to be slightly redflared.) �6�

Yoke horizontal

SPECIFIC INFORMATIONS GENERAL ADJUSTMENTS

S.V.M. COIL

1 Deflection yoke and convergence yoke. The position on the neck is required most front (CRT funnel side) and the screw is fastened after rotating yoke adjusting picture tilt. 2 Centering magnet After adjusting picture tilt, picture position is finally fixed by this magnet. In order to get maximum margin of user convergence control for center of screen, this magnet have to be used for center convergence adjustment. PREPARATION Operate the receiver for at least 5 minutes. R, G, B CUTOFF (SCREEN VR) ADJUSTMENT 1. Adjust before replace the screen assembly. 2. Set user control to reset position. CONTRAST � Max BRIGHTNESS, COLOR, TINT � Center.

(

)

3. Call up the adjustment mode display, then select the item RCUT. 4. Adjust the data of items RCUT, GCUT, and BCUT to "40H". 5. Press the -/-- button on Remote. (Y-MUTE : ON) 6. Gradually rotate R, G and B screen volume of FOCUS PAC clockwise or counterclockwise until the raster appears slightly on the CRT through the each lens, and leave them. (Lookin to the lens in order to check the raster.) 7. Press the -/-- button on Remote. (Return to Normal Picture)

Quizás también quiera comprar

$4.99

40PW03G TOSHIBA
Diagrama del circuito

Conjunto de diagramas del circuito. Los diagramas serán proporcionados en un archivo PDF. El archiv…
>
Parse Time: 0.193 - Number of Queries: 103 - Query Time: 0.046