HARTKE 3500
Manual de Usuario

Setting Up and Using The Model 2000/3500
7. Experiment with altering the balance of the two Pre-Amp knobs, listening to the effect each has on the overall sound. Depending upon the specific instrument you are using and your personal taste, you may prefer the sound of one over the other, or you may prefer a particular blend of the two. Note that, when both are used at equal settings, the amplifier will be twice as loud as when only one is used. In step #4 on the previous page, we recommended that you begin with both knobs at their midway �5� setting, but the two Pre-Amp knobs can in fact be set to any blend you like. However, you will usually want to avoid setting both to their maximum �10� position since this setting will almost always result in undesirable distortion. 8. When you have settled on a Pre-Amp balance, the next step is to adjust the two Contour (bass and treble equalizer) controls to taste. For more information, see the �About Equalization� section on page 13 of this manual. When you get a great setting that complements your instrument and playing style, it�s a good idea to write it down for future use. 9. Next, experiment with the Model 2000/3500 graphic equalizer. Begin by setting each of the ten sliders to their flat �0� center detented position. Then press in the In/Out switch (to its �In� position) so that the graphic equalizer is activated. Finally, move each slider in turn as you play your bass. For more information, see the �About Equalization� section on page 13 of this manual. Again, when you get a graphic equalization setting that complements your instrument and playing style, it�s a good idea to write it down for future use. 10. Now try out the Model 2000/3500 compression circuitry. Activate it by turning the Compression knob clockwise from its �Off� position (you�ll hear a click when it is activated). As you turn the knob clockwise, the input signal from your bass becomes more and more severely compressed�you�ll hear peak signals (such as string slaps and pulls) begin to sound increasingly �squashed,� relative to the lower-level signals produced by standard playing. The result will be a decreased dynamic range but an overall leveling of signal throughout the full pitch range of your instrument. For more information, see the �About Compression� section on page 15. In the Model 3500, the Compression LED will light steadily green when no compression is being applied, will go out whenever small amounts of compression are being applied and will flash or light steadily red when limiting (severe compression) is being applied. 11. If you�re using an external signal processor, turn your Hartke amplifier off momentarily and then connect a standard audio cable between the Effect Send jack and your effects processor input and another standard audio cable between the Effect Return jack and your effects processor output (if required, multiple effects processors can be daisy-chained together, output to input). If you are using a Hartke 3500, start with the effect Balance knob at its center detented �0� position, so that you hear equal amounts of both the send and return signal.* Then turn the amp back on and play your bass while adjusting the controls of your outboard effects processor(s). For best results, set both the input and output gain of all connected effects processor(s) to 0 dB (unity gain), so that there is no increase or decrease in level whether the effects are switched in or out. If you have followed all the steps above and are still experiencing difficulties, call Samson Technical Support (516-932-1062) between 9 AM and 5 PM EST. * For more information on the use of the Hartke 3500 effect Balance control, see page 10 in this manual. 14
2 1 0 �
GRAPHIC EQUALIZER
30Hz 64Hz 125Hz 250Hz 500Hz 1KHz 2KHz 3KHz 5KHz 8KHz +15 +12 +9 +6 +3 +2 -2 -3 -6 -9 -12 -15 30Hz 64Hz 125Hz 250Hz 500Hz 1KHz 2KHz 3KHz 5KHz 8KHz

PRE AMP A
4 3 2 1 5 6 7 9 3 1 82 4

B
5 6 7 9 8

0

10

0

10

TUBE

SOLID STATE

CONTOUR
5 10 15 -18 3 0 3 5 5 3 0 3 5 10 15 +18

10 10 15 +18 15 -18

LOW PASS

HIGH PASS

IN

+15

0

OUT
-15

3

4

5

6

7 8 9

COMPRESSION

EFFECT

RETURN

SEND

Model 2000 Effect Send/Return jacks
EFFECT
SEND

RETURN

BALANCE 0

SEND

RETURN

Model 3500 Effect Send/Return jacks and Balance control