PANASONIC WVQ150S
Manual de Usuario

Installations (continued)
3. Install the inner shell. Slide the covers located on the both lateral sides of the camera and put the inner shell on the camera until the hooks inside the inner shell are held in the holes of the camera (until a click is heard). Important: Put the inner shell down on the camera until the outside cover of the camera cannot be seen from the opening (from which the camera lens is visible) of the inner shell. If this integration is not successfully performed, the inner shell may be removed or the hidden part at the top of the screen may become larger in the WIDE mode.
Inner shells

Note: When the camera lens is pointed in the horizontal direction, the inner shell interferes with the camera�s view, and consequently about upper half of the monitor screen is hidden in the WIDE mode.

Hook

Cover Put on until a click is heard

Specifications
Ambient temperature: Dimensions: Weight: Finish: �10 °C - +50 °C {14 °F - 122 °F} 165 (W) x 206.5 (H) x 217.5 (D) mm {6-1/2" (W) x 8-1/3" (H) x 8-9/16" (D)} Approx. 950 g {2.10 lbs.} Main body: Treatment steel Top and bottom covers: ABS resin with silver metallic coating Dome cover: Acrylic resin

How to remove the inner shell Press the inner shell from the front and rear sides inward (at the same vertical position as the hooks) to bend the shell and remove the shell from the camera.

Press from the front and rear sides inward to bend

Standard Accessories
Operating Instructions (this book) ............................. 1 pc. The following are for installation. Template .................................................................... 1 sheet Inner shell .................................................................. 1 pc.

4. Mount the top cover on the wall and run the cables. Secure the top cover in either of the following two ways: q and w. No screw is supplied. Procure screws according to the installation area. q M4 screws, 4 positions (a) or w M4 screws, 2 positions ((a) upper 2 positions, not available in lower positions) and M6 or M8 anchor bolts, 2 positions (b)

(a)

(a)

(b)

(a)

(a)

(b)

Important: The length of the anchor bolt projecting portion (the distance between the tip of the anchor bolt and the chassis attaching surface) shall be 7 mm {1/4"} or less. Failure to observe this causes interference between the anchor bolt and bottom cover. Therefore, the bottom cover cannot be mounted.

7 mm {1/4"}

Anchor bolt

5. Mount the camera. Refer to "Installations/Connections" in the Installation Guide of WV-NS202 for further information. The camera mounting bracket is already attached to this bracket at the time of purchase.

Safety wire Camera fixing screw

6. Mount the bottom cover. Be sure to push the bottom cover up until a click is heard. Important: Do not let the cables be caught during installation work.

For U.S., Canadian and Puerto Rican fields:
Panasonic System Solutions Company, Unit Company of Panasonic Corporation of North America
Security Systems www.panasonic.com/security For customer support, call 1.877.733.3689 Executive Office: Three Panasonic Way 2H-2, Secaucus, New Jersey 07094 Zone Office Eastern: Three Panasonic Way, Secaucus, New Jersey 07094 Central: 1707 N. Randal Road, Elgin, IL 60123 Southern: 1225 Northbrook Parkway, Suwanee, GA 30024 Western: 6550 Katella Ave., Cypress, CA 90630

For European and other fields:

Matsushita Electric Industrial Co., Ltd.
Osaka, Japan http://panasonic.net

Panasonic Canada Inc.

Bottom cover

5770 Ambler Drive,Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 http://www.panasonic.ca

7. Tighten the fixing screw to be used for cover fall prevention. Recommended tightening torque: 1.6 N·m {16 kgf·cm}

Panasonic Sales Company Division of Panasonic Puerto Rico Inc.

San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina P.R. 00985(809)750-4300

© 2006 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.