ALPINE TMEM750
Manual de Usuario

TME-M750
R

68P21523Y50-O

6.5-inch Mobile Color Monitor
s OWNER�S MANUAL � Please read before using this equipment. s �
� �

Printed in Japan (S)

(RCS PONTOISE B 338 101 280) Sankei Kikaku Co., Ltd. 1-13-38, Hinodai, Hino, Tokyo, Japan

English

Points to Observe for Safe Usage
Read this manual carefully before starting operation and use this system safely. We cannot be responsible for problems resulting from failure to observe the instructions in this manual. This manual uses various pictorial displays to show how to use this product safely and to avoid harm to yourself and others and damage to your property. Here is what these pictorial displays mean. Understanding them is important for reading this manual. Meaning of displays � �

Warning Caution
WIDE COLOR LCD MONITOR TME-M750

This label is intended to alert the user to the presence of important operating instructions. Failure to heed the instructions will result in severe injury or death. This label is intended to alert the user to the presence of important operating instructions. Failure to heed the instructions can result in injury or material damage.

Warning
DO NOT DISASSEMBLE OR ALTER. Doing so may lead to accident, fire or electric shock. KEEP SMALL ARTICLES OUT OF THE REACH OF CHILDREN. If swallowed, consult a physician immediately. USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may result in fire or electric shock. USE ONLY IN VEHICLES WITH A 12 VOLT NEGATIVE (�) GROUND. Check with your dealer if you are not sure. Failure to do so may result in fire or electric shock.

TV TUNER INPUT

NAVIGATION INPUT

DISPLAY OUTPUT

POWER SUPPLY

MOBILE COLOR MONITOR TME-M750

AUX INPUT 2
PHONE OUTPUT VIDEO L AUDIO R VIDEO

AUX INPUT 1
L AUDIO R

POWER

VOLUME DN UP
SELECT

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE (�) BATTERY TERMINAL. Failure to do so may result in electric shock or injury due to electrical shorts. DO NOT CUT AWAY THE WIRE SHEATH AND USE POWER FOR OTHER EQUIPMENT. Doing so may exceed the current carrying capacity of the wire and result in fire or electric shock. DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION OR CREATE HAZARDS FOR VEHICLE OCCUPANTS. Doing so may obstruct forward vision or hamper movement. DO NOT CONTACT, DAMAGE OR OBSTRUCT PIPES, FLUID LINES OR WIRING WHEN DRILLING HOLES. Failure to take such precautions may result in fire or cause an accident or injuries. DO NOT USE NUTS OR BOLTS IN THE BRAKE SYSTEM WHEN MAKING INSTALLATION OR GROUND CONNECTIONS. Never use safety-related parts such as bolts or nuts in the steering or brake systems or tanks to make wiring installations or ground connections. Using such parts could disable control of the vehicle and cause brake failure, other accident or injury. HALT USE IMMEDIATELY IF A PROBLEM APPEARS. When problems occur such as a lack of sound or video, foreign objects inside the unit, smoke coming out, or noxious odors, stop use immediately and contact the dealer where you bought the equipment. Failure to do so may result in an accident or injury. DO NOT OPERATE THE EQUIPMENT OR LOOK AT THE SCREEN WHILE DRIVING THE VEHICLE. Operating the equipment may distract the driver from looking ahead of the vehicle and cause accident. Always stop the vehicle in a safe location before operating this equipment. DO NOT INSTALL THE MONITOR NEAR THE PASSENGER SEAT AIR BAG. Ensure that the location chosen for the monitor does not interfere with the operation of the passenger seat air bag. This will prevent the triggered air bag from launching the display towards passengers, possible causing injury. MAKE THE CORRECT CONNECTIONS. Failure to do so may cause fire or accident to occur. ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED. Route the cables and wiring so as not to be crimped by moving parts or make contact with sharp or pointed spots which might damage the wiring. Failure to do so may cause failure of unit or vehicle. DO NOT RAISE THE VOLUME EXCESSIVELY. Keep the volume at a level where you can still hear outside noises while driving. Driving while unable to hear outside noises could be the cause of accident. DO NOT USE THIS EQUIPMENT FOR PURPOSES OTHER THAN STATED FOR THE VEHICLE. Failure to do so may result in electric shock or injury. HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this unit to have the work done.

Caution
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place as parts that come loose can create hazards. DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST. Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may cause smoke or fire.

Parts Identification
Monitor
WIDE COLOR LCD MONITOR TME-M750

1 POWER button 2 DOWN ( ) button 3 UP ( ) button 4 SELECT button Notes: � This unit will automatically detect the NTSC and PAL video standards. � In the PAL mode, characters may freeze or banding may occur in some images. Make sure you have selected the correct video mode for your system.

1 2 3 4 � �

POWER

VOLUME DN UP
SELECT

1

23

4

Operation
Screen Display ON/OFF
Screen Display ON/OFF Press the POWER button. To turn off the POWER, press the POWER button again. Notes: � If properly connected, the monitors main POWER will turn off when the vehicle�s ignition switch is off. If the main power lamp illuminates in the STAND BY mode, the vehicle�s battery may be discharged. � On Screen Display Operating the monitor functions will be displayed On Screen for 3 seconds.
POWER

� �

1
POWER

2

Adjusting the Volume Adjust the volume level by pressing the DOWN ( ) or UP ( ) button. Mode switching Press the SELECT button. Each press of the button will cycle through the modes as follows:
NAVIGATION AUX1 AUX2 TV NAVIGATION NAVIGATION AUX1 AUX2 TV NAVIGATION

2
Adjusting the Volume

DN

UP

Adjustment Press and hold the SELECT button for at least 1 second. Each press of the button will cycle through the modes as follows:
BRIGHT COLOR TINT DIMMER DIMMER LEVEL DISPLAY MODE SOUND OUT BRIGHT
BRIGHT COLOR TINT DIMMER DIMMER LEVEL DISPLAY MODE SOUND OUT BRIGHT

2
Mode switching
SELECT

Adjustment

1
SELECT

2
SELECT

3
DN UP

4
SELECT

Adjust by pressing the DOWN ( ) or UP ( ) button. � BRIGHT: Adjust the brightness of the picture. � COLOR: Change the color balance of the picture. Note: The color adjustment is disabled when using the RGB connection or if TV mode selected. � TINT: Adjust the tint of the picture. Note: The color adjustment is disabled when using the RGB connection or if TV mode selected. � DIMMER: AUTO: Backlighting of the monitor adjusts automatically to the ambient light available inside the vehicle. LOW: Backlighting is set to its lowest level. MAX: Backlighting is set to its maximum level. � DIMMER LEVEL: Adjust the backlighting output level. � DISPLAY MODE: WIDE: Expands a normal broadcast picture to fit the entire screen. CINEMA: Displays a widescreen formatted picture (16:9) to fit the entire screen. ZOOM: Displays a normal broadcast picture to fit the entire screen by cropping the left and right video information. NORMAL: Displays a normal broadcast picture without modification. Black stripes will appear at left and right of the screen. � SOUND OUT MONITOR: Outputs sound through the built-in speakers. HEADPHONES: Outputs sound to headphones if connected. After completing adjustments, press and hold the SELECT button for at least 1 sec. Notes: � After turning the system off, a slight ghost of the image will remain temporarily. This is an effect peculiar to LCD technology and is normal. � Under cold temperature conditions, the screen may lose contrast temporarily. After a short warm-up period, it will return to normal. � It is normal for a very small number of the screen�s pixels to be off. Even under the very high precision manufacturing conditions, this fact is unavoidable.

� � � �

� �

�

� � �

R

ALPINE ELECTRONICS, INC. Tokyo office: 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-8501, Japan Tel.: (03) 3494-1101 ALPINE ELECTRONICS OF AMERICA, INC. 19145 Gramercy Place, Torrance, California 90501, U.S.A. Tel.: 1-800-ALPINE-1 (1-800-257-4631)

ALPINE ITALIA S.p.A. Via C. Colombo 8, 20090 Trezzano Sul Naviglio MI, Italy Tel.: 02-48 40 16 24 ALPINE ELECTRONICS FRANCE S.A.R.L. (RCS PONTOISE B 338 101 280) 98, Rue De La Belle Etoile, Z.I. Paris Nord II B.P. 50016 F-95945, Roissy, Charles de Gaulle Cedex, France Tel.: 01-48 63 89 89

In Case of Difficulty
If you encounter a problem, please review the item in the following check list. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer. Symptom No function or display. Cause Car's ignition is off. No fuse or blown fuse. Incorrect connections. Unclear picture display. No picture display. Vehicle's battery is weak. Fluorescent tube is exhausted. Brightness control is set for minimum brightness control. Incorrect setting of the VCR mode. Protective circuit is on because of high temperature. Incorrect or open connection with the Monitor, AV Interface unit. Picture colour is poor. Spots or dotted lines/stripes appear. * Brightness/Colour/Tint control are not set to the proper positions. Caused by neon signs, high-voltage power lines, CB transmitter, other vehicle's ignition plugs, etc. Turn the ignition on. Check the cause and replace the fuse. Check connection and remedy. Check the voltage of vehicle's battery. Replace the fluorescent tube*. Adjust the brightness. Switch to the correct mode. Wait until the temperature inside the vehicle comes down to the operating temperature range (45°C). Check the connection and remedy. Check each control. Change the location of your vehicle. Solution

ALPINE ELECTRONICS OF CANADA, INC. Suite 203, 7300 Warden Ave. Markham, Ontario L3R 9Z6, Canada Tel.: 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD. 6-8 Fiveways Boulevarde Keysborough, Victoria 3173, Australia Tel.: (03) 9769-0000 ALPINE ELECTRONICS GmbH Kreuzerkamp 7-11 40878 Ratingen, Germany Tel.: 02102-45 50

ALPINE ELECTRONICS OF U. K., LTD. 13 Tanners Drive, Blakelands, Milton Keynes MK14 5BU, U.K. Tel.: 01908-61 15 56 ALPINE ELECTRONICS DE ESPA�A, S.A. Portal De Gamarra 36, Pabellón 32 01013 Vitoria (Alava) - Apdo. 133, Spain Tel.: 34-45-283588

The fluorescent tube replacement is not free of charge even within the warranty period, for the tube is an article of consumption.