JVC TK-C215V12U
Manual de Usuario

Installation and connection (continued) 6. Set the switches for video images.

Installation and connection (continued)
Mounting
(TK-C215V4 A pg. 10) (TK-C215V12 A pg. 12) (TK-C210FW A pg. 14)

Mounting the Camera to the Ceiling (continued)
When mounting the camera directly to the ceiling or on the wall
When mounting to a wall, replace areas indicated as �ceiling� in the procedures by �wall�.

1. Align the position mark of the fastened
Adaptor ring

outer case with that of the camera unit. When doing so, be careful not to catch the cables in the outer case.

4. 6.
A

5.

NOTE:

Pan fastening Screw

1.

2. Turn the camera unit in the clockwise
Attach from the ceiling slab

Setup
Make use of the template supplied to open a hole.
Camera Fastening Screw Fall prevention wire (not supplied)
F UP RON T

1. Open a hole in the ceiling. (R30 mm) 2. Draw the fall prevention wire mounted to
CAUTION:

2.

the ceiling slab and the cable out from the ceiling in advance.

3.

direction. T When doing so, ensure that the X mark is visible. (See illustration below) 3. Fasten the camera by tightening the camera fastening screw.
Position mark

C
Be sure to loosen the screw.

� Select a suitable safety cable based on length, strength, location, material (insulation property), etc. � Use a ring on the fall prevention wire for mounting to the camera unit with an internal diameter of at least R3.1 mm or and not larger than R5.5 mm, and an external diameter that is not larger than R 9 mm.

4. B
1.
*TK-C215V4 is used in the above illustration

2.
T Check

Connecting

1. Align j with the shooting direction when
mounting the cover to the ceiling. Mount by using the supplied adapter ring to clamp between the outer case and the ceiling. Notes on outer case mounting screws (not supplied): � The diameter of the attachment hole of outer case is R4.5 mm (3/16 inch). � Do not use flathead screws. � When using an impact screwdriver, do not tighten the screws fully. Tighten using your hand instead. Failure to do so may damage the outer case.

*TK-C215V4 is used in the above illustration

4. Connect the video signal cable. (A pg. 14)
Lower the protection cover and connect the connectors. Upon connecting, restore the protection cover to cover the connectors. Connect the input power supply cable. (A pg. 15) (A pg. 14)

3. Remove the dome cover.
As illustrated in the diagram, hold the dome ring such that the position mark comes between the thumb and index finger. Turn the ring in the anti-clockwise direction to remove.

5.

Camera fastening screw

6. Install the Ferrite core (TK-C210FW only) 7. Connect the alarm cable.
(TK-C215V12 only) (A pg. 15)

3.

8. Wrap insulation tape around cables.

3.
*TK-C215V4 is used in the above illustration

2. Hang the fall prevention wire that has been
Dome Ring Position mark

dismantled in Step 4 C of the setup procedures to the hook.

4. Remove the outer case.
A Loosen the camera fastening screw with a
screwdriver.

3. Attach the fall prevention wire to the
CAUTION:

Alarm signal cable (TK-C215V12 only)

Adjusting Images
After mounting is completed, adjust the images while checking the actual image. (A pg. 23 AAdjusting ImagesB)

camera. (Fall prevention wire is not included)

5.7. 4.

Solder or crimp

B To remove, turn the camera unit in the anticlockwise direction.

C Dismantle the fall prevention wire. CAUTION:

� Tighten all screws securely. Otherwise the camera may come loose and fall.

5. Loosen the pan fastening screw.
� Moving the lens unit without loosening the pan fastening screw may damage the lens unit.

Protection cover

Insulation tape

8.

Wrap with tape Input power supply cable

*TK-C215V12 is used in the above illustration

20

21