SONY SPPN1003
Manual de Usuario

Making and receiving calls
Making calls

Speed dialing
You can dial with a touch of a few keys by storing a phone number on a dialing key.

1 2
(FLASH)
TALK/BATT LOW lamp VOL switch

Pick up the handset from the base unit. Press (TALK), and wait until the TALK/BATT LOW lamp lights up. The dialing keys light up. You then hear a dial tone. If you hear beeps, move closer to the base unit. Dial the phone number. When you�re done talking, press (OFF). The TALK/BATT LOW lamp goes off.

Storing phone numbers

1 2
TALK/BATT LOW lamp

Press (PGM). The TALK/BATT LOW lamp flashes. Press (SPEED DIAL). The dialing keys light up. Press one of the dialing keys ((0) to (9)) to store a phone number on. You hear a confirmation beep. Enter the phone number you want to store. You can enter up to 20 digits, including a tone and a pause, each of which is counted as one digit. Press (PGM). You hear a long confirmation beep, and number is stored. The TALK/ BATT LOW lamp goes off.

2
(* TONE)

3

4
3 4
(REDIAL/PAUSE)

1, 5 4 2
5
(REDIAL/PAUSE)

Microphone

(CHANNEL/RINGER)

Receiving calls

1

When you hear the phone ring; � Press (TALK) (or any key except (OFF)). or � Pick up the handset from the base unit when the handset is placed on the base unit. The TALK/BATT LOW lamp lights up.

Note Do not allow more than 20 seconds to elapse between each step of the procedure. Tips � If you enter a wrong number, press (PGM), then start from the beginning. � Affix the supplied directory to a desired place.

To store a number to be dialed via Private Branch Exchange (PBX)
Before entering a phone number in step 4, do as follows:

2

When you�re done talking, replace the handset on the base unit or press (OFF). The TALK/BATT LOW lamp goes off.
Do this Set the VOL switch to H (high), M (middle) or L (low). Press (* TONE) after you�re connected. The line will remain in tone dialing until disconnected. While the handset is not in use, press (CHANNEL/RINGER). Each press of (CHANNEL/RINGER) switches the ringer type by one of four type. Press (FLASH). Press the button again to get back to the first caller.

1 Enter the outside line access digit (e.g., 9). 2 Press (REDIAL/PAUSE).
To change a stored number
Store a new number, as described previously.
Note You can replace the stored number with a new number, but you cannot just erase it.

Additional tasks
To Adjust the handset volume Switch to tone dialing temporarily Set the ringer type Switch to another call (�call waiting service�*)

Making calls with speed dialing 1 Press (TALK) and wait until the TALK/BATT LOW lamp lights up.
The dialing keys light up.

2 Press (SPEED DIAL). 3 Enter the desired speed dialing number ((0) to (9)).
The phone number stored in the speed dialing number will be dialed.

* You need to subscribe to the service from your telephone company.
Notes � Do not cover the microphone during the conversation; otherwise, the other party cannot hear your voice. � If you hear beeps during the conversation, move closer to the base unit; otherwise, the call will be disconnected after 15 seconds. Note that, however, you may not hear beeps if it�s noisy on the handset.

Paging
You can page the handset from the base unit. Note that you cannot page if the handset is in use.

If interference occurs on the handset
When you press (TALK), the handset automatically searches for the channel with the best reception. However, if you notice interference during a conversation, move closer to the base unit. If interference persists, press (CHANNEL/RINGER) to switch to another channel to improve the sound quality of your telephone conversation.
Note If you hear five short beeps when you press (CHANNEL/RINGER), move closer to the base unit.

Press (HANDSET LOCATOR). The handset rings for about one minute. To end the page, press (OFF) on the handset.

(HANDSET LOCATOR)

If the handset battery becomes weak during a call
The handset will beep every three seconds with the TALK/BATT LOW lamp flashing at the same time. Finish your call and charge the battery pack.
Caution If this occurs, you cannot use the handset without charging it for more than one minutes.

Mounting the base unit on a wall
1 2
Attach the telephone line cord and AC power adaptor cord to the base unit. Bundle the loose telephone line cord or AC power adaptor cord, if necessary. Plug the telephone line cord into the telephone outlet, and hook the base unit to the wall plate as illustrated. Plug the AC power adaptor to an AC outlet. Then raise the antenna so that it points towards the ceiling.

Redialing
1 Press (TALK), and wait until the TALK/BATT LOW lamp lights up. 2 Press (REDIAL/PAUSE) to redial the number last dialed.
Note If the number exceeds 32 digits, the beeps will alert you that the number cannot be dialed.

1
Bundle the loose telephone line cord or AC power adaptor cord, if necessary. Telephone line cord AC power adaptor cord

2
Wall plate

To erase the last phone number dialed
Press (REDIAL/PAUSE) twice. The number will be erased from the memory, and you�ll hear a long confirmation beep.

AC outlet

AC power adaptor