JVC RX-9000VBKJ
Manual de Usuario

3) Repeat 1) and 2) to adjust the other speaker output levels.

6. Adjust the room size (sense of spaciousness).
BALANCE/SURROUND ADJUST

BALANCE/SURROUND ADJUST

3. Adjust the center tone.

1) Press BALANCE/SURROUND ADJUST repeatedly until �CENTER TONE� appears on the display. The display changes to show the current setting. 2) Turn MULTI JOG to select the center tone level you want. � As you turn it, the display changes to show the following: CENTER SHARP1 CENTER SHARP2
MULTI JOG

1) Press BALANCE/SURROUND ADJUST repeatedly until �ROOM SIZE� appears on the display. The display changes to show the current setting. 2) Turn MULTI JOG to select the room size. � As you turn it, the room size changes as follows:

MULTI JOG

ROOM SIZE 1

ROOM SIZE 2

ROOM SIZE 3

ROOM SIZE 5

ROOM SIZE 4

CENTER FLAT
(Canceled)

As the number increases, the interval between reflections increases so that you will feel as if you were in a larger room.

CENTER SOFT 1

CENTER SOFT 2

(Normally set it to �ROOM SIZE 3.�)

7. Adjust the liveness.
To make the dialogue clearer, select �CENTER SHARP1� (a little) or �CENTER SHARP2� (much). To make the dialogue softer, select �CENTER SOFT 1� (a little) or �CENTER SOFT 2� (much). When �CENTER FLAT� is selected, no adjustment is applied. 1) Press BALANCE/SURROUND ADJUST repeatedly until �LIVENESS� appears on the display. The display changes to show the current setting. 2) Turn MULTI JOG to select the liveness effect. � As you turn it, the liveness level changes as follows:

BALANCE/SURROUND ADJUST

MULTI JOG

4. Adjust the rear tone.
1) Press BALANCE/SURROUND ADJUST repeatedly until �REAR TONE� appears on the display. The display changes to show the current setting. 2) Turn MULTI JOG to select the rear tone level you want. � As you turn it, the display changes to show the following:
REAR SHARP1 REAR FLAT
(Canceled)

BALANCE/SURROUND ADJUST

LIVENESS 1

LIVENESS 2

LIVENESS 3

LIVENESS 5
MULTI JOG

LIVENESS 4

As the number increases, the attenuation level of reflections over time decreases so that acoustics change from �Dead� to �Live.� (Normally set it to �LIVENESS 3.�)

REAR SHARP2

From the remote control: When using the remote control, you cannot adjust the effect level, room size, and liveness. To adjust these parameters, use the buttons and controls on the front panel.

REAR SOFT 1

REAR SOFT 2

To make the rear sounds clearer, select �REAR SHARP1� (a little) or �REAR SHARP2� (much). To make the rear sounds softer, select �REAR SOFT 1� (a little) or �REAR SOFT 2� (much). When �REAR FLAT� is selected, no adjustment is applied.

1. Press SURROUND MODE repeatedly until �LARGE THEATER (or DIG L. THEATER,

SURROUND MODE

DTS L. THEATER)� or �SMALL THEATER (or DIG S. THEATER, DTS S. THEATER)� appears on the display.
SOUND

5. Adjust the overall level of the effects.
1) Press BALANCE/SURROUND ADJUST repeatedly until �EFFECT LEVEL� appears on the display. The display changes to show the current setting. 2) Turn MULTI JOG to select the effect level. � As you turn it, the effect level changes as follows:
BALANCE/SURROUND ADJUST

2. Press SOUND.
The 10 keys are activated for sound adjustments.

3. Press TEST to check the speaker output balance.
MULTI JOG

TEST

10
RETURN

�TEST TONE L� starts flashing on the display, and a test tone comes out of the speakers in the following order:

TEST TONE L
EFFECT 1 EFFECT 2 EFFECT 3 EFFECT 4
(Left front speaker)

TEST TONE C
(Center speaker)

TEST TONE R
(Right front speaker)

EFFECT 5

TEST TONE LS
(Left rear speaker)

TEST TONE RS
(Right rear speaker)

As the number increases, the overall level of reflections applied to the direct sounds increases. (Normally set it to �EFFECT 3.�)

Continued to the next page.

37