JVC RX-7010VBKC
Manual de Usuario

English

2. Press CONTROL UP 5/DOWN � to select the delay time of the rear speaker output.

CONTROL DOWN UP

Low Frequency Effect Attenuator Setting
If the bass sound is distorted while playing back a source using Dolby Digital or DTS Digital Surround, follow the procedure below.

� Press CONTROL UP 5 to increase the delay time from 0 msec (�R_DELAY 0MS�) to 15 msec (�R_DELAY 15MS�). � Press CONTROL DOWN � to decrease the delay time from 15 msec (�R_DELAY 15MS�) to 0 msec (�R_DELAY 0MS�).

On the front panel ONLY:

1. Press SETTING repeatedly until �LFE ATT� (Low Frequency Effect Attenuator) appears on the display.
The display changes to show the current setting.

T SETTING

Notes:
� Rear delay time is not valid for the DVD MULTI playback mode. � You cannot adjust the rear delay time when you have set �REAR SPK� to �NO.�

2. Press CONTROL UP 5/DOWN � to select the low frequency effect attenuator level.
� Each time you press the button, the display changes to show the following:

CONTROL DOWN UP

Crossover Frequency Setting
Small speakers cannot reproduce the bass sound very well. So, if you have used a small speaker for any of the front, center, and rear channels, this receiver automatically reallocate the bass elements, originally assigned to the channel for which you have connected the small speaker, to another channel (for which you have connected the large speaker). To use this function properly, you need to set the crossover frequency level according to the size of the small speaker connected. � If you have selected �LARGE� for all speakers (see page 14), this function is set to �OFF� and cannot be adjusted.

0dB
0dB: 10dB:

10dB

Normally select this. Select this when the bass sound is distorted.

Notes:
� Low frequency effect attenuator is not valid for the DVD MULTI playback mode. � This function takes effect only when the subwoofer (LFE) signals come in, (with �SUBWOOFER� set to �YES.�)

On the front panel ONLY:

1. Press SETTING repeatedly until �CROSSOVER FRQ� (Crossover Frequency) appears on the display.
The display changes to show the current setting.

ST SETTING

Dynamic Range Compression Setting
You can compress the dynamic range (difference between maximum sound and minimum sound) of the reproduced sound. This is useful when enjoying surround sound at night. � This function takes effect only when playing back a source using Dolby Digital.

2. Press CONTROL UP 5/DOWN � to select the crossover frequency level according to the size of the small speaker connected.
the following:

CONTROL DOWN UP

On the front panel ONLY:

� Each time you press the button, the display changes to show

80HZ

100HZ

120HZ

1. Press SETTING repeatedly until �D_RANGE COMP� (Dynamic Range Compression) appears on the display.
The display changes to show the current setting.

ST SETTING

� Use the following comments as reference when adjusting. 80HZ: 100HZ: 120HZ: Select this when the cone speaker unit built in the speaker is about 4 3/4 inches (12 cm). Select this when the cone speaker unit built in the speaker is about 3 15/16 inches (10 cm). Select this when the cone speaker unit built in the speaker is about 3 3/16 inches (8 cm).

2. Press CONTROL UP 5/DOWN � to select the appropriate item about the compression level.
� Each time you press the button, the display changes to show the following:

CONTROL DOWN UP

OFF
OFF: MID: MAX:

MID

MAX

Note:
Crossover frequency is not valid for the DVD MULTI playback mode and HEADPHONE mode.

Select this when you want to enjoy surround with its full dynamic range. (No effect applied.) Select this when you want to reduce the dynamic range a little. (Factory setting.) Select this when you want to apply the compression effect fully. (Useful at night.)

Note:
Dynamic Range Compression is not valid for the DTS Digital Surround and DVD MULTI playback mode.

15